# Local Water & Mold: full text of the national guides > Every guide that applies in all states, plus the glossary and state statistics. Each section names its source URL; please cite that URL. Index: https://localwatermold.com/llms.txt Guide · Appliances # Washing machine, dishwasher, fridge and toilet leaks Appliance supply lines are among the most common causes of indoor water damage, and almost every one has its own shutoff valve within arm's reach. Here's where to find it. The short answer - Every water-using appliance should have its own shutoff: behind the washer (two valves, hot and cold), under the kitchen sink for the dishwasher, behind or below the refrigerator for the ice maker line, and at the wall behind the toilet. Turn it clockwise to close. - For an overflowing toilet, lift the tank lid and push the flapper down, or lift the float, then close the valve behind the toilet. - Rubber washing machine hoses are a frequent failure point. Replace them about every five years, or switch to braided stainless steel hoses. - Water from a washer or dishwasher is gray water (Category 2), so wear gloves for cleanup and dry or remove soaked materials within 24 to 48 hours. - Leak sensors and automatic shutoff valves are inexpensive, and some insurers take them into account when pricing a policy. ## Shutoffs and common failures | Appliance | Shutoff | What usually fails | | Washing machine | Two valves on the wall behind it | Rubber fill hoses that burst; drain hose popping out of the standpipe; a clogged standpipe overflowing | | Dishwasher | Under the kitchen sink | Supply line connection, door gasket, drain hose, or a pump seal | | Refrigerator | Behind or below the fridge, or under the sink | Thin plastic ice maker line cracking or loosening; clogged defrost drain | | Toilet | Oval handle on the wall behind it | Supply line, fill valve, cracked tank, wax ring at the base | | Kitchen and bath sinks | Two valves under the sink | Braided supply lines, drain trap connections, garbage disposal | | Water softener or filter | Bypass valve on the unit | Fittings and the drain line | ## Stopping an overflowing toilet - **Lift the tank lid** and press the rubber flapper at the bottom of the tank closed, or lift the float so the fill valve stops. - **Close the supply valve** on the wall behind the toilet, turning it clockwise. - **Treat the water by what's in it.** Clean tank water is Category 1; an overflow with urine is Category 2; anything with feces, or sewage coming up from the drain, is Category 3 and calls for gloves, boots and disinfection. - **Check below.** On upper floors, look at the ceiling underneath for stains or dripping, and switch off any light fixture there. ## Cleaning up - Unplug the appliance or switch off its breaker before touching it or the water around it. - Mop and extract standing water, and pull the appliance out to dry behind and underneath it. - Check under kitchen cabinets and behind toe kicks; water hides under cabinet bases and laminate flooring. - Photograph the failed hose or line and keep it for your insurer. - If water reached the ceiling below, wall cavities or a finished basement, get a professional moisture inspection. ## Prevent the next one - **Upgrade hoses and lines.** Braided stainless steel washer hoses and ice maker lines resist bursting. Even braided lines should be replaced periodically. - **Leave room behind the washer** so the hoses don't kink against the wall. - **Add leak sensors** on the floor by the washer, dishwasher, fridge, water heater and under sinks. - **Consider an automatic shutoff valve** that closes the main when a sensor detects water or flow runs too long. - **Turn off the washer valves** when you travel, or shut off the main for long trips. ## Frequently asked questions **Where is the shutoff valve for my washing machine?** Usually on the wall behind the washer, in a recessed box or on two pipes: one for hot and one for cold. Turn both clockwise. If there's no valve or it won't turn, shut off the main water valve. **Where does the dishwasher water shut off?** Most dishwashers are fed by a small line from a valve under the kitchen sink, sometimes shared with the hot water faucet line. Turn it clockwise. Also switch off the dishwasher's breaker or unplug it before pulling it out. **Why is water on the floor in front of my refrigerator?** Common causes are a cracked or loose ice maker or water dispenser supply line, a clogged defrost drain that overflows inside the fridge, or a full or cracked drain pan underneath. Close the ice maker supply valve and check behind and under the fridge. **Why is my toilet leaking at the base?** A leak at the base when you flush usually means the wax ring seal between the toilet and the floor flange has failed. It can soak the subfloor and the ceiling below for months before it shows, so fix it promptly. ## Sources - U.S. EPA WaterSense: Fix a Leak Week - IICRC: ANSI/IICRC S500 Standard for Professional Water Damage Restoration - Insurance Information Institute: Am I covered? --- Guide · Mold # Black mold: what it is, health effects and what to do "Black mold" isn't a scientific category, and color doesn't tell you how dangerous a mold is. What matters is how much is growing, where, and who lives in the house. The short answer - "Black mold" usually refers to Stachybotrys chartarum, a greenish-black mold that grows on wet, cellulose-rich materials such as drywall paper and wood. But many common molds are black too, and the CDC advises treating all molds the same when it comes to health risks and removal. - Any mold can cause stuffy nose, wheezing, and red or itchy eyes or skin, and people with asthma, allergies or weakened immune systems are more sensitive. The CDC says no test proves a link between Stachybotrys and particular health symptoms. - Testing is usually unnecessary. The CDC doesn't recommend routine mold sampling, and there are no set standards for acceptable mold levels in a home. If you can see or smell mold, remove it and fix the moisture source, whatever the species. - The EPA suggests a homeowner can usually clean an area under about 10 square feet (roughly 3 feet by 3 feet). Larger areas, mold inside walls or HVAC, mold after sewage, or anyone with health concerns call for a professional. ## What people mean by black mold Most of the time, "black mold" means Stachybotrys chartarum. It needs material that stays wet for a long time, such as drywall paper, ceiling tile or wood after a slow leak or flood, which is why it's a sign of a serious moisture problem. But other common molds, including species of Cladosporium, Alternaria and Aspergillus, can also look black or dark green, and they're far more common on bathroom grout, window sills and damp basements. The species matters less than the moisture. Mold won't grow without water, and it will come back after cleaning if the leak, condensation or humidity isn't fixed. ## Health effects - **Most people:** mold can cause stuffy nose, sore throat, coughing or wheezing, burning eyes and skin rash. - **People with allergies or asthma:** reactions can be stronger, and mold can trigger asthma attacks. - **People with weakened immune systems or chronic lung disease:** are at higher risk of infection and should avoid moldy areas and cleanup work. If you have symptoms you think are related to mold, see a doctor. Mold remediation companies can remove mold, but they can't diagnose health problems. ## Can you clean it yourself? The EPA's guidance for homeowners uses a size threshold of about 10 square feet. Below that, cleanup is usually a do-it-yourself job if the mold isn't from sewage and no one in the house is at higher risk. - **Fix the water first.** Repair the leak, dry the area, and lower humidity below 60% (ideally 30% to 50%). - **Protect yourself.** Wear an N95 respirator, gloves and goggles without vent holes. - **Scrub hard surfaces** with detergent and water, then dry them completely. - **Remove porous materials** that are moldy, such as drywall, ceiling tile, insulation and carpet. Bag them before carrying them through the house. - **Don't paint or caulk over mold.** It keeps growing underneath and the paint will peel. ## When to call a remediation company - The growth covers more than about 10 square feet, or keeps coming back. - It's inside walls, under floors, in the attic or crawl space, or in the heating and cooling system. - It followed a sewage backup or floodwater. - Someone in the house has asthma, a weakened immune system, or symptoms you think are mold-related. Professional remediation under the IICRC S520 standard sets up containment with plastic sheeting and negative air pressure so spores don't spread, removes contaminated materials, cleans with HEPA vacuums, and dries the area. Ask the company whether it also fixes the moisture source or whether you'll need a separate contractor. ## When mold testing makes sense - You smell mold but can't find it, and want to narrow down where it is. - You want clearance testing after a professional remediation, done by an independent assessor rather than the company that did the work. - A landlord, buyer, insurer or court requires documentation. ## Frequently asked questions **Is black mold dangerous?** All indoor mold growth should be removed, but black-colored mold isn't automatically more dangerous than other mold. Molds can cause allergy-like symptoms and asthma attacks, and people with weakened immune systems or chronic lung disease can develop infections. The amount of growth, how long you're exposed and your own health matter more than the color. **How do I know if it's black mold?** You can't tell the species by looking at it, and in most cases you don't need to. Treat any visible mold the same way: fix the water problem, then clean or remove the moldy material. **Should I get a mold test?** Usually not. The CDC doesn't recommend routine sampling, because there are no set standards for acceptable mold levels and results can't tell you whether someone will get sick. If mold is visible, testing doesn't change what you need to do. Testing can help in specific cases, such as tracking down a hidden source behind a persistent smell, or clearance testing after a professional remediation. **Can I clean black mold with bleach?** On hard, non-porous surfaces, scrubbing with detergent and water and drying completely is usually enough, and is what the EPA recommends. If you use bleach, the CDC advises no more than 1 cup per gallon of water, ventilating well, and never mixing bleach with ammonia or other cleaners. Porous materials like drywall, ceiling tile and carpet that are moldy usually have to be removed, not cleaned. **Can I stay in my house with black mold?** For small areas, most healthy people can stay while it's cleaned up. For large areas, or if someone in the house has asthma, a weakened immune system or is getting sick, talk with a doctor and consider staying elsewhere during professional remediation, when the work area should be sealed off. ## Sources - CDC: Mold - CDC: Facts about Stachybotrys chartarum - U.S. EPA: A Brief Guide to Mold, Moisture and Your Home - U.S. EPA: Mold cleanup in your home - IICRC: ANSI/IICRC S520 Standard for Professional Mold Remediation --- Guide · Emergency # Water damage: call your insurance company or a restoration company first? It's the first decision after the water stops, and the internet gives opposite answers. The short version: make it safe, document, start drying, and notify your insurer the same day. Waiting for permission is the expensive mistake. The short answer - **Safety and the shutoff come before any phone call.** Then photograph and video everything before anything is moved. - **Start drying fast.** The EPA advises drying wet materials within 24 to 48 hours to prevent mold. Homeowners policies also expect you to protect the property from further damage. That usually means calling a water mitigation company the same day. - **Notify your insurer the same day too**, by phone or app. Ask for a claim number and whether they need to approve the mitigation company or will send one. - **Mitigation first, rebuild later.** Drying and removing wet materials is urgent. Repairs and rebuilding can wait for the adjuster and an agreed scope. - **Small, clean and quick to dry?** You may not need either call. See whether you can dry it yourself before deciding to file a claim. ## The short answer Both calls, same day, in this order: **safety, shutoff, photos, start drying, notify your insurer.** The mistake that costs people money isn't calling in the wrong order. It's letting wet drywall, carpet and subfloor sit for days while waiting for an adjuster's permission, then discovering mold and a smaller payout. ## Why drying can't wait for the adjuster - **Mold starts fast.** The EPA advises drying wet building materials and furnishings within **24 to 48 hours** to prevent mold growth. Adjusters, especially after storms, often can't come that fast. - **Your policy expects it.** Standard homeowners policies list "duties after loss" that include giving prompt notice and **protecting the property from further damage**. Damage that gets worse because nobody dried it can be harder to claim. - **Mitigation is different from repair.** Extracting water, removing soaked materials that can't be saved, and setting up drying equipment is mitigation. Rebuilding walls and replacing floors is restoration. Insurers expect the first quickly and want to agree the second. ## Minute by minute - **Make it safe.** Stay out of water near outlets or the electrical panel, leave if you smell gas, keep out from under sagging ceilings. Full steps in what to do before help arrives. - **Stop the water** at the fixture valve or the main shutoff. - **Document before moving anything:** a walk-through video, photos of the source and waterlines, and keep the failed part. - **Call a water mitigation company** if more than a small area is wet, the water is gray or black, it reached walls, ceilings or a lower floor, or it has been wet for more than a day. - **Notify your insurer** by phone or app. Get a claim number. Ask: do you need to approve the mitigation company, or will you send one? - **Keep a log:** who you called, when, and what they said. Save every receipt, including fans, tarps and hotel nights. ## What to say when you call your insurer A clear first call sets the tone of the claim: "I'm reporting water damage at my home. It started around [time] on [date] from [source]. It affected [rooms or areas]. I've stopped the water and photographed everything. A mitigation company is [coming at time / I'd like your recommendation]. Can you give me a claim number, tell me who my adjuster will be, and tell me if you need anything before drying starts?" Ask them to note in the file that you started mitigation to prevent further damage. ## What to ask the restoration company - When can you arrive, and what will you do on the first visit? - Will you take **moisture readings and photos** each day and share them? (Professional drying under the IICRC S500 standard is measured, not guessed.) - Do you bill my insurer directly, and **what happens if part of it isn't covered**? - What exactly am I signing? Read work authorizations and assignments of benefits before you sign anything. ## When you might not file a claim at all If the water was clean, the area is small and it can be dried within a day or two, the cost may be below your deductible, and claims can affect future premiums. Get the facts first: can you dry it yourself? and what restoration costs. Telling your insurer about a loss and filing a claim for payment aren't always the same step; ask your agent how your insurer treats an inquiry. ## If the insurer wants its own company Many insurers have preferred restoration vendors. They can make approval smoother, but in most cases you can still choose your own company. The trade-offs are in the insurer's vendor or your own contractor. ## Find a restoration company near you Each state section lists county pages with local restoration help and that state's insurance regulator and claim rules: Alabama, Arkansas, Georgia, Illinois, Indiana, Iowa, Kansas, Kentucky, Maryland, Michigan, Minnesota, Mississippi, Missouri, Nebraska, New York, North Carolina, Ohio, Oklahoma, Pennsylvania, South Carolina, Tennessee, Texas, Virginia, West Virginia, Wisconsin. ## Frequently asked questions **Should I call my insurance company before a water damage restoration company?** Do both on the same day, but don't wait for the insurer before stopping further damage. Make the area safe, document it, start drying (usually by calling a mitigation company), and notify your insurer promptly. Most homeowners policies expect you to take reasonable steps to protect the property from further damage. **Will my insurance deny the claim if I hire a restoration company before the adjuster comes?** Not for that reason alone, as long as you documented the damage first, told your insurer promptly and the work was reasonable emergency mitigation. Keep photos, receipts and the company's moisture readings. Avoid major demolition or rebuilding before the adjuster has seen the damage or agreed to it. **Does the insurance company have to send its own restoration company?** Insurers often offer a company from their network, and some ask you to use one for faster approval. In most cases you can choose your own. Ask the insurer what changes if you do, and read the separate guide on preferred vendors. **Should I file a claim for small water damage?** Not always. If the damage is clean water, small, and dries within a day or two, the repair may cost less than your deductible, and a claim can affect future premiums. Get an estimate first, then decide. **What should I say when I call my insurer?** When and where the water started, what caused it, which rooms are affected, that you have stopped the water and documented it, and what mitigation you have arranged. Ask for the claim number, the adjuster's contact and whether they need anything before work starts. ## Sources - U.S. EPA: A Brief Guide to Mold, Moisture and Your Home - NAIC: Homeowners insurance claims, what to do after a loss - Insurance Information Institute: Understanding the insurance claims payment process - IICRC: ANSI/IICRC S500 Standard for Professional Water Damage Restoration --- Guide · Inside the industry # Your belongings after water or fire damage: pack-outs, cleaning, storage and the inventory that gets you paid The structure of your house is one job. Everything inside it is another, often run by a different department or company, billed in a different way and paid under a different part of your policy. It's also where homeowners lose the most money without noticing, usually in a dumpster. The short answer - **Contents is a separate job and a separate claim.** Belongings fall under personal property coverage (often Coverage C), with its own limits, depreciation and inventory requirements. - **A pack-out moves belongings off site** for cleaning and storage. It makes sense after fires and large water losses, or when rooms must be emptied for rebuilding. For a single wet room, moving items within the house is often enough. - **Pack-out, cleaning and storage are billed item by item, box by box and month by month.** Storage keeps billing as long as the rebuild takes, so ask what your policy will pay and for how long. - **Never let anything be thrown away undocumented.** Every discarded item needs a photo, a description and your sign-off. Without that, it can't be claimed. - **Many policies pay actual cash value first** and release the depreciation once you replace an item. Keep receipts and watch the deadline. ## Two jobs, two claims When water or smoke damages a house, there are really two losses: the **building**, including walls, floors, cabinets and built-ins, and the **contents**, meaning everything you could pick up and take with you. Insurance treats them separately. The building is usually dwelling coverage; your belongings usually fall under personal property coverage, often labeled Coverage C, with its own limit and its own rules. Restoration companies often split them too. Many have a separate contents department, and some send contents work to a specialist company. That means a separate estimate, separate invoices and a separate set of decisions, often made fast, in the first day or two, while you're still dealing with the water. ## Pack-out or move it within the house? | | Content manipulation | Pack-out | | **What happens** | Furniture and items are moved to a dry room or raised on blocks so drying can happen | Items are inventoried, packed and taken to the company's facility for cleaning and storage | | **When it fits** | One or two rooms of clean water, with dry space elsewhere in the house | Fire and smoke, large water losses, contaminated water, or rooms that must be empty for rebuilding | | **How it's billed** | Usually by the hour or by the room | Inventory, packing materials, labor, transport, cleaning by item and storage by the month | | **Cost** | Modest | Often thousands of dollars, and storage keeps adding up | A pack-out is a real service and often the right call. It's also one of the more profitable parts of a restoration job, so it's sometimes suggested when moving things across the hall would do. You can accept, decline or limit it. Ask your adjuster what they'll approve before you agree. ## How contents work is billed - **Inventory:** listing and photographing each item or box, often in specialized software. - **Packing:** labor plus boxes, wrap and crates, often per box. - **Transport** to and from the facility. - **Cleaning,** priced by item and method: wiping hard goods, ultrasonic cleaning for small hard items, laundering or dry cleaning textiles, ozone or other odor treatment after smoke. - **Storage,** usually by vault or by space, **per month**. - **Pack-back:** unpacking and placing items when you move back in. **The meter that keeps running:** storage bills every month until the rebuild finishes. If the rebuild drags on for permits, insurance disputes or contractor delays, storage can grow into one of the larger lines in the claim. Ask your adjuster early how long storage will be paid, and ask the company for monthly statements. ## The inventory is your claim For contents, insurers pay for what's documented. The inventory made during a pack-out, with photos, is often the backbone of your personal property claim. Two items on that list deserve the most attention: - **Salvageable items** are cleaned and returned. The claim covers the cleaning, not the item. - **Non-salvageable items** are discarded and claimed for their value. Each needs a description, an approximate age and what it would cost to replace. Ask for a copy of the inventory as it's built, not just at the end. Add anything that's missing, such as items in closets, drawers or the garage, and correct descriptions that undersell what you owned. "Sofa" and "three-seat leather sofa, purchased 2021" lead to very different payments. ## Nothing gets thrown away undocumented This is where homeowners lose the most money. In the rush of the first day, wet carpet, soaked furniture and boxes of damaged belongings go to the dumpster. Without photos and a list, they're very hard to claim later. - **Photograph every item before it leaves,** with any brand label or model number visible. - **List it** with a description, rough age and replacement cost. - **Keep samples** where you can: a piece of the carpet and pad, a corner of a damaged rug, fabric from upholstery. - **Ask your adjuster** whether they want to see anything before it's discarded, especially high-value items. - **Sign off only on items you've seen listed.** Ask for the disposal list in writing. ## What can usually be saved Whether something can be saved depends on the material, the category of water, and how long it was wet. | Item | Clean water, caught quickly | Contaminated water | | **Dishes, glass, metal, hard plastic** | Clean and keep | Usually cleanable with disinfection | | **Clothing and linens** | Launder or dry clean | Often cleanable by specialist laundering | | **Solid wood furniture** | Often restorable | Sometimes, depending on finish and exposure | | **Upholstered furniture** | Sometimes, if dried quickly | Usually discarded | | **Mattresses and box springs** | Sometimes, if only surface wet | Discarded | | **Books, documents, photos** | Often saved by freezing, then freeze-drying | Specialist recovery for irreplaceable items | | **Electronics** | Don't power on; specialists can test and clean | Specialist assessment | | **Food, medicine, cosmetics** that got wet | Discard | Discard | **Papers and photos:** if you can't deal with them right away, put them in sealed bags in the freezer. Freezing stops mold and gives you time to find a document recovery service. The National Archives publishes guidance on saving family papers and photographs. ## Irreplaceable and high-value items Restoration contents departments are good at volume. Fine art, antiques, heirlooms, musical instruments and quilts may need a **specialist conservator**. You can ask for those items to be handled separately and ask your adjuster whether specialist restoration will be covered. It often costs less than replacement, which makes it easier to approve. ## How contents are paid - **Actual cash value (ACV) first:** many policies pay replacement cost minus depreciation for age and wear. - **Recoverable depreciation:** with replacement cost coverage, the depreciation is usually paid once you replace the item, within a deadline set by the policy. Keep every receipt. - **"Like kind and quality":** insurers price replacements with comparable items. If the comparison item is lower quality than what you owned, show them listings for genuinely equivalent items. - **Special limits:** jewelry, firearms, collectibles, cash and some electronics often have lower limits unless separately scheduled. ## The pack-back - **Check items against the inventory** as they come back, before signing a delivery receipt. - **Open boxes of fragile items** while the crew is still there. - **Note any odor** on textiles or furniture that went out for smoke cleaning. - **Report damage or missing items in writing** right away, to the company and your adjuster. ## Before the next time: a home inventory A ten-minute video walk-through of each room, opening closets and drawers, saved somewhere other than your house, makes any future contents claim far easier. Narrate as you go: what each item is, roughly when you bought it and what it cost. ## State claim rules Each state section covers its claim rules and insurance regulator: Alabama, Arkansas, Georgia, Illinois, Indiana, Iowa, Kansas, Kentucky, Maryland, Michigan, Minnesota, Mississippi, Missouri, Nebraska, New York, North Carolina, Ohio, Oklahoma, Pennsylvania, South Carolina, Tennessee, Texas, Virginia, West Virginia, Wisconsin. ## Frequently asked questions **What is a pack-out in water damage restoration?** A pack-out is when a restoration company inventories, photographs, packs and moves your belongings to its facility for cleaning and storage while your house is dried and repaired. They're returned in a pack-back when the work is done. **Do I have to let the restoration company pack out my belongings?** No. It's a service you can accept, decline or limit. It's often worthwhile after a fire or a large water loss, or when rooms must be emptied for rebuilding. For smaller jobs, moving items to a dry part of the house may be enough. Ask your adjuster what they'll approve before agreeing. **Who pays for contents cleaning and storage?** Usually your homeowners insurance, under personal property coverage, if the loss is covered. Storage is billed monthly, so ask your adjuster how long it will be paid and whether there's a limit, especially if the rebuild may take months. **Can water-damaged items be saved?** Many can. Hard items like dishes, glass and metal usually clean well. Clothing and many fabrics can be laundered. Documents and books can often be saved by freeze-drying. Porous items soaked in contaminated water, like mattresses and upholstered furniture, are usually discarded under the IICRC S500 standard. **What should I do before the restoration company throws something away?** Make sure every item is photographed and listed with a description, age and approximate value, and ask for a copy of that list before it's disposed of. Keep a sample of materials like carpet and pad if possible. Your insurer may want to see items before they're thrown out. ## Sources - NAIC: Consumer guide to homeowners insurance - IICRC: ANSI/IICRC S500 Standard for Professional Water Damage Restoration - National Archives: Saving family papers and photographs after water damage --- Guide · Crawl spaces # Crawl space water and mold: causes and fixes A damp crawl space can rot floor framing, grow mold, and send musty air into the rooms above. The fix depends on where the water is coming from. The short answer - Crawl spaces get wet three ways: rain and groundwater from outside, leaking plumbing or ductwork, and condensation when humid summer air meets cool surfaces. - Start outside. Gutters that dump at the foundation and soil that slopes toward the house cause many wet crawl spaces, and are usually inexpensive to fix. - A **vapor barrier** is plastic sheeting over the dirt floor that slows ground moisture. **Encapsulation** goes further: it seals the floor and walls, closes vents, and dries the space with a dehumidifier or conditioned air. - Standing water needs drainage and often a sump pump before any barrier goes in. Mold on floor joists should be cleaned and the moisture source fixed, or it returns. ## Find the source first | Source | Clues | Usual fix | | Rain and surface water | Water after storms, worst near downspouts or low corners | Extend downspouts, clean gutters, regrade soil away from the house | | Groundwater | Water seeping through walls or up through the floor in wet seasons; high water table | Perimeter drain and sump pump, then a vapor barrier | | Plumbing leaks | Wet spot under a bathroom, kitchen or water heater; water year-round | Repair the pipe, dry the area, replace wet insulation | | Ductwork | Wet insulation and condensation on ducts in summer; disconnected duct | Seal and insulate ducts, reconnect loose runs | | Summer condensation | Damp joists and dripping pipes in humid weather with no rain | Ground vapor barrier, air sealing, and dehumidification or conditioning | ## Vapor barrier, encapsulation and drainage - **Vapor barrier:** polyethylene sheeting laid over the dirt floor, with seams overlapped and taped. It's the basic step that slows moisture rising from the soil. - **Encapsulation:** a heavier liner over the floor and up the walls, sealed at seams and piers, with vents and rim joists sealed, and a dehumidifier or a small supply of conditioned air to keep humidity in check. - **Drainage:** an interior perimeter drain that carries water to a sump pump. It's needed when liquid water collects; a liner alone just hides the water underneath. - **Insulation:** in a sealed crawl space, insulation usually moves from between the floor joists to the walls. Fiberglass batts that are wet or falling down should be removed. ## Questions to ask a contractor - Where is the water coming from, and how will you fix the source, not just cover it? - What liner thickness are you using, and how are seams, piers and walls sealed? - How will the space be dried afterward: dehumidifier, supply air from the HVAC system, or both? Who maintains it? - Do you need a permit, and does the design meet local code for crawl space ventilation and combustion appliances? - Is mold on the framing being cleaned, treated or removed, and is that in the written scope? ## Test for radon before sealing Sealing a crawl space changes how air moves between the soil and the house. Where soil gas contains radon, the U.S. Department of Energy notes that air-sealing can raise indoor radon levels, so test first and plan for mitigation if levels are high. ## Signs it's working A crawl space that's under control stays below about 60% relative humidity, has no standing water after storms, and has no musty smell drifting into the house. A cheap hygrometer left in the crawl space and checked through a summer will tell you more than any sales pitch. ## Frequently asked questions **Is some moisture in a crawl space normal?** Crawl spaces are rarely bone dry, but standing water, wet insulation falling from the joists, visible mold, condensation dripping from ducts or pipes, and wood moisture readings consistently above about 19% to 20% are signs of a problem. **Should crawl space vents be open or closed?** Vents were meant to dry crawl spaces, but in humid summers they can let in warm, moist air that condenses on cool joists and ducts. Many building scientists now recommend sealed, conditioned crawl spaces in humid climates. Don't simply close vents without adding a ground vapor barrier and a way to dry the air; local building codes set the requirements. **Is crawl space mold dangerous?** Air from the crawl space moves up into the house, so mold and musty odors there can affect indoor air. People with asthma or allergies are most likely to notice. Fix the moisture, clean or remove the moldy material, and seal gaps between the crawl space and the living space. **Does insurance cover crawl space water?** Water from a sudden plumbing failure usually is covered. Groundwater, seepage, flooding and long-term humidity or condensation usually aren't, because insurers treat them as maintenance or as excluded flood and surface water. ## Sources - U.S. Department of Energy, Building America: Unvented crawlspaces - U.S. EPA: A Brief Guide to Mold, Moisture and Your Home - U.S. EPA: Moisture control guidance for building design, construction and maintenance --- Guide · Insurance # Does homeowners insurance cover water damage? Usually yes, if the water was sudden and accidental and came from inside the house. Usually no, if it built up slowly, rose from outside, or backed up from a sewer without the right endorsement. The short answer - A standard homeowners policy (the common HO-3 form) generally covers water damage that is **sudden and accidental**, such as a burst pipe, a split washing machine hose or a water heater that fails. - It generally **excludes** damage from a slow leak or lack of maintenance, flooding or surface water from outside, and groundwater seeping through the foundation. - **Sewer and drain backups** are excluded unless you've added a water backup endorsement. **Flood** needs a separate flood policy, from the National Flood Insurance Program or a private insurer, and NFIP policies usually take 30 days to start. - Policies usually pay to repair the damage the water caused, not to fix the part that failed, such as the pipe, the water heater or a worn-out roof. - Your policy wording decides. Read the declarations page and the water, mold and exclusions sections, and ask your insurer to confirm coverage in writing. ## Covered vs. usually not covered | Cause | Standard homeowners policy | What else might cover it | | Burst or frozen pipe | Usually covered, if sudden and heat was maintained | — | | Washing machine, dishwasher or ice maker line failure | Usually covered | — | | Water heater tank failure | Water damage usually covered; the heater itself usually not | Home warranty, for the appliance | | Toilet overflow | Usually covered if sudden | — | | Roof leak after wind, hail or a fallen tree | Usually covered | — | | Roof leak from age or wear | Roof repair usually not covered | — | | Ice dam leak | Interior water damage often covered | — | | Slow leak over weeks or months | Usually not covered | — | | Sewer or drain backup | Not covered without an endorsement | Water backup endorsement; some city programs | | Sump pump failure or overflow | Not covered without an endorsement | Water backup and sump discharge endorsement | | Flood, storm surge or surface water from outside | Not covered | NFIP or private flood policy | | Groundwater seeping through the foundation | Not covered | Usually nothing; it's treated as maintenance | | Mold | Sometimes covered when it follows a covered loss, often capped | Mold endorsement on some policies | General patterns for the common HO-3 form. Policies, endorsements and state rules differ. Your policy language controls. ## The test insurers apply: sudden and accidental Homeowners policies are written to cover sudden events, not maintenance. When an adjuster looks at water damage, the questions are usually where the water came from, when it started, and whether the homeowner could have known about it and stopped it. A pipe that split during a cold snap is sudden. A shower pan that seeped into the subfloor for a year, leaving rot and staining, is gradual. That's why documentation matters. Photos and video of the source, the failed part itself, and a note of when you found the water all help show that the damage was sudden. ## What the policy pays for, and what it doesn't - Usually paid: water extraction and drying, removal and replacement of damaged drywall, flooring, cabinets and trim, and damaged belongings under your personal property coverage. - Often paid: the cost of tearing out and replacing part of a wall or floor to reach the broken pipe. - Usually not paid: the failed item itself, such as the corroded pipe, the worn-out water heater or the old roof. - Loss of use: if a covered loss makes the home unlivable, additional living expenses for a hotel or rental and extra meal costs. ## Flood insurance is separate Homeowners policies exclude flood: water that rises from outside and covers normally dry land, from rivers, heavy rain, storm surge or overwhelmed storm drains. Flood coverage comes from the National Flood Insurance Program, run by FEMA and sold through insurance agents, or from private flood insurers. - NFIP policies generally have a 30-day waiting period before coverage starts, so you can't buy one when a storm is already on the way. - NFIP building coverage goes up to $250,000 and contents up to $100,000 for a home. - In basements, NFIP coverage is limited to items such as furnaces, water heaters, electrical panels, sump pumps and cleanup. Finished walls, floors and most belongings stored in a basement aren't covered. ## Sewer backup coverage is an add-on Water that backs up through floor drains, toilets or tubs from a sewer line or a failed sump pump is excluded from most standard policies. A water backup endorsement adds it, usually with its own limit. It's often inexpensive compared with the cost of a sewage cleanup, and worth asking your agent about if you have a basement. Some cities also run backup assistance programs; check before you pay for cleanup. ## How to protect your claim - Stop the water and make the home safe. Policies require you to protect the property from further damage, and the cost of reasonable emergency steps is usually part of the claim. - Document before cleanup. Take video and photos of every affected room and the source, and keep the failed part. - Notify your insurer promptly. Ask for the claim number, your adjuster's contact details, and whether they need to approve a mitigation company before work starts. - Start drying. Waiting for an adjuster before drying can turn a drying job into a mold job. Most insurers expect mitigation to begin right away. - Keep every receipt and an inventory of damaged belongings, with photos, ages and approximate values. - Get decisions in writing. If the insurer denies part of the claim, ask for the specific policy provision it relies on. ## Your state's rules Each state sets its own deadlines for how fast insurers must acknowledge, investigate and pay claims, and runs a consumer help line for complaints. Our state guides cover those rules and your state insurance regulator: - Alabama water damage claims - Arkansas water damage claims - Georgia water damage claims - Illinois water damage claims - Indiana water damage claims - Iowa water damage claims - Kansas water damage claims - Kentucky water damage claims - Maryland water damage claims - Michigan water damage claims - Minnesota water damage claims - Mississippi water damage claims - Missouri water damage claims - Nebraska water damage claims - New York water damage claims - North Carolina water damage claims - Ohio water damage claims - Oklahoma water damage claims - Pennsylvania water damage claims - South Carolina water damage claims - Tennessee water damage claims - Texas water damage claims - Virginia water damage claims - West Virginia water damage claims - Wisconsin water damage claims ## Frequently asked questions **Does homeowners insurance cover a burst pipe?** Usually yes, for the water damage it causes, if the pipe burst suddenly. Many policies exclude freeze damage if the house was vacant or unheated and you didn't maintain heat or shut off and drain the water. The cost of repairing the pipe itself is often not covered, although the cost of opening and closing the wall to reach it may be. **Does homeowners insurance cover a slow leak?** Usually not. Damage from a leak that continued over weeks or months, or that happened because of wear, rot or lack of maintenance, is a common exclusion. Some policies cover hidden leaks you couldn't reasonably have known about, so check the wording. **Is a flooded basement covered by homeowners insurance?** It depends on where the water came from. A burst pipe or failed water heater in the basement is usually covered. Water from a sewer or drain backup, or from a failed sump pump, is covered only if you have a water backup endorsement. Groundwater seepage and floodwater from outside are excluded and need flood insurance, and even NFIP flood policies cover only limited items in basements. **Does homeowners insurance cover mold?** Mold that results from a covered sudden water loss is often covered, sometimes up to a capped sublimit. Mold from long-term humidity, condensation or a slow leak usually isn't. Some policies exclude mold entirely. **Does homeowners insurance cover a roof leak?** If wind, hail or a falling tree suddenly damaged the roof, the roof repair and the water damage inside are usually covered. If the roof leaked because it was old or worn out, the roof repair usually isn't, and interior damage may be disputed. **Should I file a claim for small water damage?** Compare the likely cost with your deductible. If the damage is close to or below the deductible, a claim pays little and may still appear in your claims history. If you're unsure how far water spread, get a moisture inspection first; hidden water inside walls and floors often makes the job bigger than it looks. **Will my insurance pay for a hotel if I can't live at home?** If the damage comes from a covered loss and makes your home unlivable, most homeowners policies include loss of use coverage (often called additional living expenses or Coverage D) for the extra cost of living elsewhere. Keep every receipt. ## Sources - Insurance Information Institute: Am I covered? - FEMA FloodSmart: What a flood insurance policy covers for homeowners - FEMA FloodSmart: Basement flooding and NFIP coverage --- Guide · Drying # How long does water damage take to dry? With professional equipment, most clean-water jobs dry in three to five days. Hardwood, plaster and concrete take longer, and air-drying on your own can take weeks while mold gets a head start. The short answer - A typical clean-water job dried with professional air movers and dehumidifiers takes about **3 to 5 days**. - Dense materials take longer: hardwood floors often 1 to 2 weeks or more, plaster walls and concrete slabs sometimes several weeks. - The EPA advises drying water-damaged materials within **24 to 48 hours** to prevent mold, so the goal of the first day is to get water out and equipment running, not to finish. - A job is dry when moisture meter readings in wet materials match readings from the same material in an unaffected part of the house (the "dry standard"), not when surfaces feel dry or a set number of days has passed. ## Typical drying times by material These are rough ranges for clean water with professional drying equipment started within a day. Gray or black water, long delays, cold or humid weather, and water trapped under other materials all add time. | Material | Typical drying time | Notes | | Carpet (pad replaced) | 1 to 3 days | Pad is usually pulled and replaced; carpet dried in place. | | Drywall, lightly wet | 2 to 4 days | Longer behind cabinets, tile or vinyl wallpaper. | | Wood subfloor and framing | 3 to 7 days | Moisture must come out of the wood itself, not just the surface. | | Hardwood flooring | 1 to 2 weeks or more | Often dried with specialty floor mats; some cupping can relax as it dries. | | Plaster and lath | 1 to 3 weeks | Dense and slow to release water; common in older homes. | | Concrete slab or block | Several weeks | Basement slabs and block walls hold water deep in the material. | ## What a professional drying setup does - **Extraction** removes standing water and squeezes water out of carpet and pad. Water removed as liquid is far faster than water evaporated. - **Air movers** push air across wet surfaces to speed evaporation. - **Dehumidifiers** pull that evaporated moisture out of the air so it doesn't settle back into materials. - **Moisture mapping** with meters and thermal cameras shows how far water traveled inside walls and floors, and where to aim equipment. - **Daily readings** track progress, so equipment is moved or removed based on data. ## What slows drying down - Waiting. Every hour water sits, it wicks higher into drywall and deeper into wood. - Layers that trap water: vinyl flooring over a subfloor, tile, cabinets, or several layers of flooring. - Cold, damp weather or a humid summer, especially in basements. - Turning equipment off at night to save noise or power. - Contaminated water, which means removal and cleaning before drying can even start. ## How to tell it's actually dry Professionals measure moisture in the wet materials and compare it with readings from the same material in an unaffected room of the same house. That reference is the "dry standard." Equipment should come out when wet areas reach it, and the company should be able to show you the readings. Ask for the drying log if your insurer is paying; it documents that the job was done properly. ## When drying turns into removal Some materials can't be dried economically or safely. Carpet pad, insulation, particleboard, laminate and drywall that's swollen, crumbling or touched by sewage are usually removed. If drying hasn't started within a couple of days and there's a musty smell or visible growth, treat it as a mold problem as well as a drying job. ## Frequently asked questions **Can I dry water damage myself with fans?** For a small, clean spill on a hard floor that you catch right away, household fans, open windows and a dehumidifier are often enough. Once water has soaked into carpet pad, run under baseboards or wicked up drywall, household fans dry surfaces but leave moisture inside the wall and subfloor, where mold can grow unseen. A moisture meter reading is the only reliable check. **How long does drywall take to dry after a leak?** Lightly wet drywall can dry in two to four days with air movers and dehumidifiers. Drywall that wicked water up more than a foot or so, or that's behind vinyl wallpaper or cabinets, may need small holes drilled or the lower section removed so air can reach the cavity. **Can wet carpet be saved?** Often, if it was clean water and drying starts within a day or two. The pad underneath is usually replaced because it holds water and is cheap. Carpet soaked by sewage or floodwater should be discarded. **Why are the dehumidifiers still running when the floor feels dry?** Surfaces dry first. Moisture inside subfloors, wall cavities and the bottom of drywall takes longer to come out, and a good company keeps equipment running until meter readings match the dry standard. **Is it normal for the house to feel warm during drying?** Yes. Air movers and dehumidifiers give off heat, and warm, dry air pulls moisture out of materials faster. Don't turn the equipment off or open windows on humid days without asking the technician; it can slow drying. ## Sources - U.S. EPA: A Brief Guide to Mold, Moisture and Your Home - IICRC: ANSI/IICRC S500 Standard for Professional Water Damage Restoration - U.S. EPA: Mold cleanup in your home --- Guide · Inside the industry # How water damage estimates are really priced: estimating software, price lists and the line items that move the total Your restoration company and your insurer probably wrote their estimates in the same program, using the same regional price list. So why are the totals thousands apart? Because the fight is almost never about the price of a line. It's about which lines are there, and how many of each. The short answer - **Most insurance restoration work is estimated in Xactimate**, software from Verisk that carries a price list for each region, updated monthly. Contractors and insurers usually price from the same list. - **Because unit prices are shared, the money moves through quantities:** how many air movers, how many days, how many square feet of drywall, which water category, and whether a line appears at all. - **The lines worth questioning** are equipment days, equipment counts, flood-cut height, water category, content manipulation, containment, and overhead and profit (O&P). - **O&P is commonly 10% overhead plus 10% profit**, added when a general contractor coordinates several trades. Whether your insurer owes it depends on your policy and your state, so ask rather than assume. - **Read any estimate in this order:** the summary page, the room-by-room quantities, the equipment and labor lines, then the notes. Twenty minutes with the photos and moisture logs beside it catches most problems. ## One program prices most of this industry When an adjuster writes an estimate for a burst pipe, they almost always build it in **Xactimate**, estimating software made by Verisk. Most restoration companies that do insurance work use it too, because insurers expect to see estimates in that format. Xactimate doesn't let anyone type a price for "fix the basement." It works in coded **line items**: remove wet drywall, per square foot; air mover, per 24-hour period; apply antimicrobial, per square foot. Each line is priced from a **price list for your region**, researched and updated every month. The estimator's job is to pick the right lines and enter the right quantities. The software does the multiplication. That has a consequence most homeowners never hear about: **when your contractor and your insurer disagree, they usually aren't disagreeing about prices.** They're often using the same price list for the same month. The difference is in what each one included and how much of it. ## Anatomy of a line item Every line on an Xactimate-style estimate has the same parts. Once you can read one, you can read all of them. | Part | What it means | Example | | **Description** | What's being done or used | Air mover (per 24-hour period), no monitoring | | **Quantity and unit** | How much, in what unit: EA (each), SF (square feet), LF (linear feet), HR, DA (day) | 12.00 EA, meaning 3 machines for 4 days | | **Unit price** | From the regional price list, sometimes split into material, labor and equipment | Whatever your area's list says this month | | **Tax** | Sales tax on materials, where it applies | Varies by state | | **O&P** | Overhead and profit, if applied | Often a separate column or a line at the end | | **Total** | Quantity times unit price, plus tax and O&P | | Look at the quantity column first. That's where almost every difference between two estimates lives. ## Where the money actually moves These are the lines that move a water damage estimate up or down. None of them is wrong in itself. Each one should be supported by something you can see: a photo, a moisture reading, a measurement. | Line | Why it moves the total | What supports it | | **Equipment days** | Every machine bills every day it runs. One extra day across eight machines adds up quickly. | Daily moisture logs showing materials still above the drying goal | | **Equipment count** | The IICRC S500 standard gives placement guidelines based on the room and how wet it is, so counts should be explainable. | A room-by-room list and the reasoning for the count | | **Flood-cut height** | Cutting drywall at 4 feet instead of 2 feet roughly doubles the drywall removed now and the drywall rebuilt later. | Readings or photos showing how high the water wicked | | **Water category** | Category 2 or 3 water brings protective gear, antimicrobials, containment and more removal. Calling clean water "gray" changes the whole job. | Where the water came from and how long it sat. See the three categories. | | **Content manipulation** | Moving furniture out of the way and back, billed by the hour or by the room | Photos of the furnished rooms before work started | | **Containment and air scrubbers** | Plastic walls and HEPA air filtration are expected for contaminated water or mold, but less often for a clean-water leak. | The water category, or visible growth | | **Monitoring visits** | Each daily check is a labor line. | Dated readings for each visit | | **After-hours and minimum charges** | Emergency service premiums and job minimums | When you called, and what you were told | | **Debris and haul-off** | Dumpsters, hauling and disposal fees | The amount of material actually removed | | **Supervision and project management** | Hours for coordinating the job | Usually more defensible on larger, multi-trade jobs | **The quiet multiplier:** decisions made in the first hour, like how high to cut and whether the cabinets come out, set the size of both the drying bill and the rebuild bill. They're the least visible decisions on the estimate and often the most expensive. More on that in mitigation vs. rebuild. ## Overhead and profit, explained You'll often see **O&P** at the bottom of a contractor's estimate and missing from the insurer's. It's usually calculated as **10% overhead plus 10% profit**, the long-standing convention for a general contractor who schedules and supervises other trades. - **When it's usually included:** jobs that need a general contractor to coordinate several trades, such as drywall, painting, flooring, cabinets and electrical. People in the industry often cite "three or more trades" as a rule of thumb, but that's a habit, not policy language. - **When it's often left off:** simple jobs a single trade could handle, and mitigation-only work. - **What decides it for your claim:** your policy wording and your state's rules and court decisions. If it's missing and your job clearly needs a general contractor, ask the adjuster in writing why. ## Price lists aren't quotes The regional price list is a researched estimate of what work costs in your area. Most months it's close enough that both sides accept it. It falls behind in a few situations: - **After a large storm or freeze,** when every crew in the region is booked and labor costs jump faster than the list updates. - **In rural areas,** where travel time and the small number of companies push real costs above a list built from wider data. - **For specialty work,** like drying hardwood with floor mats, cleaning electronics or freeze-drying documents, where few companies set the market. In those cases, a contractor may bill above the list and the insurer may pay at the list. That gap is real and is sometimes negotiable with evidence, such as invoices from subcontractors or quotes from other companies. ## Time and materials: the other pricing method Some mitigation companies bill **time and materials (T&M)** instead of unit prices: hours worked plus a rate for each machine. It isn't wrong, but it's harder to check against an insurer's estimate, which will almost always be written in unit prices. If your work authorization says T&M, ask for daily time sheets alongside the moisture logs. ## Why your insurer's estimate comes in lower The insurer's estimate isn't written to be generous or stingy. It's written to what the adjuster can support from the file. Lines usually go missing for one of these reasons: - **The adjuster didn't see it.** A desk adjuster working from photos can't count equipment that wasn't photographed or tear-out that happened after the inspection. - **The documentation doesn't support it.** No moisture reading for day five means no day five. - **A guideline says otherwise.** Insurers and their vendor programs often have review rules, for example on when containment is allowed or how many days drying should take. - **It isn't covered.** Some items fall under an exclusion or a sublimit, like mold or the failed part itself. The first two are fixable with paperwork. The third is negotiable when the facts of your job differ from the guideline. The fourth is a coverage question, covered in what insurance covers. ## How to read your estimate in 20 minutes - **Start with the summary page.** Note the totals for mitigation, rebuild, contents, tax and O&P, and any deductible or depreciation subtracted. - **Check each room's measurements.** Wrong room dimensions throw off every square-foot line in that room. - **Compare the equipment lines against the moisture log.** Machines times days should match the days the log shows materials still wet. - **Check removal against photos.** Every square foot of drywall, carpet or pad billed as removed should appear in a photo. - **Find the water category.** It's usually stated in the notes, and it explains most of the protective and antimicrobial lines. - **Mark each line on the two estimates** as the same, a different quantity, or missing. Send that list, not a complaint about the total, to whoever you're negotiating with. ## What this means for you You don't need to become an estimator. You need to know that the number at the bottom is a stack of small, checkable decisions, and that each decision should have evidence behind it. Ask for the photos, the moisture logs and the native estimate files early, while the job is still going. A file with good records rarely ends in a fight over the total. ## State claim rules and regulators If a disagreement with your insurer stalls, your state insurance department is the place to call. Each state section lists its regulator and claim rules: Alabama, Arkansas, Georgia, Illinois, Indiana, Iowa, Kansas, Kentucky, Maryland, Michigan, Minnesota, Mississippi, Missouri, Nebraska, New York, North Carolina, Ohio, Oklahoma, Pennsylvania, South Carolina, Tennessee, Texas, Virginia, West Virginia, Wisconsin. ## Frequently asked questions **What is Xactimate?** Xactimate is estimating software from Verisk used by most U.S. property insurers and many restoration contractors. It builds an estimate from coded line items, each priced from a regional price list that is updated monthly. Because both sides often use it, disputes are usually about quantities and which items belong, not unit prices. **If both estimates use the same software, why are they so different?** Each estimator decides which line items to include and how many of each. One might count five air movers for four days and include containment; another might count three for three days and leave containment out. The same price list multiplied by different quantities gives very different totals. **What does O&P mean on a restoration estimate?** Overhead and profit. It's usually written as 10% plus 10%, applied to the estimate when a general contractor manages several trades. Some insurers include it only when the job is complex enough to need a general contractor. Rules on when it's owed vary by policy and state. **Can I get a copy of the estimate file itself?** You can ask both your contractor and your adjuster for a copy of their estimates. Most will send a PDF. Contractors and adjusters can also exchange the native estimate file (an ESX file), which lets them compare line by line instead of arguing over totals. **Is the price list the real market price?** It's a researched estimate of local prices, not a quote. In a normal month it's often close to what work costs. After a large storm or flood, when labor is scarce, real costs can run ahead of the list for a while. That's one reason bills and estimates drift apart after disasters. ## Sources - Verisk: Xactimate property estimating software - IICRC: ANSI/IICRC S500 Standard for Professional Water Damage Restoration - NAIC: Consumer guide to homeowners insurance - Insurance Information Institute: Understanding the insurance claims payment process --- Guide · Insurance # Your insurer's preferred restoration company or your own? How to choose after water damage The adjuster says, 'We can send someone today.' It sounds like help, and often it is. But the company works within a program set up by your insurer, and it helps to know what that means before you say yes. The short answer - **A preferred vendor** is a restoration company in your insurer's network that has agreed to the insurer's pricing and documentation rules. It can mean faster approval and less paperwork for you. - **In most cases you can choose your own company.** Ask your insurer directly what changes if you do, and check your policy and your state insurance department's guidance. - **Either way, the work should be documented:** daily moisture readings, photos and an itemized estimate you can read. - **Your contract is with whoever you hire.** If something goes wrong, ask who stands behind the work: the company, the insurer's program, or both. ## What "preferred vendor" means Many insurers run programs with restoration companies that agree to their rules: response times, pricing methods, photo and moisture documentation, and how estimates are submitted. When the adjuster offers to "send someone", that's usually a company from this network. It isn't a scam, and it isn't a favor. It's a business arrangement that can genuinely make your claim easier, with one built-in tension: the company is part of a program set up by the party paying the bill. ## The honest pros and cons | | Insurer's preferred vendor | Your own company | | **Speed of approval** | Often faster: pricing and paperwork are pre-agreed | Can be slower if the insurer questions prices or scope | | **Getting someone out today** | Often good: the insurer can dispatch | Depends on local demand; a local company may be quicker | | **Who they answer to** | You, and the insurer's program rules | You | | **Price disputes** | Fewer, because prices are agreed | More likely; good documentation settles most | | **Choice** | Whoever is assigned | You can check reviews, certifications and references first | | **Guarantee** | Ask whether the program adds one | The company's own warranty | ## Do you have to use the insurer's company? In most cases, no. Your policy is a promise to pay for covered, reasonable work, not to pick your contractor. But rules and policy wording vary, so do two things before you decide: - **Ask the insurer directly:** "If I use my own restoration company, does anything change about approval, payment or guarantees?" Write down the answer and who gave it. - **Check your state insurance department** if anyone tells you that you must use a particular company. Each state's department has a consumer line; the NAIC lists them all. ## Seven questions for whichever company you choose - **Are your technicians IICRC certified** for water damage restoration? (The IICRC S500 standard is the industry's drying standard.) - **Will you take and share daily moisture readings and photos?** - **What will you remove, and why?** Ask them to explain any tear-out before they do it, unless it's an emergency. - **How do you price the job?** Many companies estimate with the same software insurers use; ask for an itemized estimate. - **Do you bill my insurer directly, and what do I owe if part isn't covered?** - **What am I signing?** A work authorization is normal. An assignment of benefits is a bigger decision; see before you sign. - **Who guarantees the work, and for how long?** ## A simple way to decide - **Choose the insurer's vendor** if speed matters most, you don't have a company you trust, and the insurer confirms the work is guaranteed. - **Choose your own company** if you have one you trust, the vendor can't come quickly, or you want to vet certifications and reviews yourself. Expect to keep documentation tidy so the bill is easy to approve. - **Either way,** photograph the damage before work starts, keep copies of all moisture logs, and don't sign anything you haven't read. ## If you choose your own company Find a local restoration company through your state section, where county pages list local help and the state's claim rules: Alabama, Arkansas, Georgia, Illinois, Indiana, Iowa, Kansas, Kentucky, Maryland, Michigan, Minnesota, Mississippi, Missouri, Nebraska, New York, North Carolina, Ohio, Oklahoma, Pennsylvania, South Carolina, Tennessee, Texas, Virginia, West Virginia, Wisconsin. ## Frequently asked questions **Do I have to use my insurance company's restoration contractor?** Usually not. Insurers often recommend a company from their preferred network, and some make the process smoother if you do, but in most cases you can hire the qualified company you choose. Ask your insurer what changes if you use your own, and check your state insurance department's guidance. **Is the insurance company's preferred vendor cheaper?** It usually works to prices agreed with the insurer, which can mean fewer disputes over the bill. That doesn't automatically mean a better or worse job; compare the scope, documentation and warranty. **Who guarantees the work if I use the insurer's vendor?** Ask before work starts. Some insurer programs offer a workmanship guarantee in addition to the contractor's own warranty; others don't. Get the answer in writing. **Can my own contractor get paid by insurance?** Yes. Insurers pay for covered, reasonable work regardless of which qualified company does it, though disagreements about price or scope are more common with out-of-network companies. Detailed documentation is what settles them. ## Sources - NAIC: Consumer guide to homeowners insurance - NAIC: Find your state insurance department - Insurance Information Institute: Understanding the insurance claims payment process - IICRC: Find a certified firm - IICRC: ANSI/IICRC S500 Standard for Professional Water Damage Restoration --- Guide · Inside the industry # Mitigation and rebuild are two different jobs: why it matters who does each, and how day-one decisions set the final bill The company that arrives at midnight to pump out your basement is hired for a few days of emergency work. But the decisions it makes in those days, what to tear out and what to dry in place, set the size of a rebuild that can cost several times more. And that company would very much like to do the rebuild too. The short answer - **Mitigation** stops and dries the water: extraction, removing what can't be saved, drying equipment. **Reconstruction** puts the house back: drywall, paint, floors, cabinets. They're different trades, estimates and often contracts. - **You don't have to hire the drying company for the rebuild.** Signing a mitigation work authorization doesn't commit you to reconstruction unless the paperwork says so, so read it. - **Tear-out decisions on day one set the rebuild bill.** A company that will also rebuild has a reason to remove more; a company paid only to dry may remove too little. Ask what can be dried in place. - **Drying in place is often possible** for cabinets, hardwood and wall cavities with the right equipment, and saves both the replacement cost and the mismatch problems. - **Rebuild payments are often made out to you and your mortgage lender**, and lenders may release large amounts in stages after inspections. Call your lender's loss draft department early. ## Two phases, two kinds of work | | Mitigation | Reconstruction | | **Goal** | Stop the damage from getting worse | Put the house back the way it was | | **Work** | Extraction, tear-out of what can't be saved, drying equipment, cleaning, antimicrobials | Insulation, drywall, paint, trim, flooring, cabinets, sometimes electrical and plumbing | | **Timing** | Starts within hours, usually lasts days | Starts after drying is confirmed, often lasts weeks | | **Who does it** | Restoration technicians | A general contractor and trades | | **Licensing** | Often no specific license, varies by place | Usually a contractor license and permits, depending on your state and city | | **Estimate** | Its own estimate or invoice | A separate repair estimate, often much larger | Many restoration companies do both. Plenty don't, and pass the rebuild to a partner or leave it to you. ## Why the drying company wants the rebuild Mitigation is fast, emergency work, and on many water jobs the rebuild is the larger part of the total. The drying crew has an advantage no other contractor has: they're already in your house, they know the damage, and you already trust them enough to let them in at midnight. So the rebuild pitch often comes before the dehumidifiers are switched off. That isn't necessarily bad. One company handling both can mean less coordination and a cleaner hand-off. But it's a **separate decision**, and you're entitled to make it separately: - **Read your mitigation paperwork** for language about reconstruction, "completion of all repairs," or a cancellation fee if you use someone else. See before you sign. - **Wait for the insurer's repair estimate** before signing a rebuild contract. It's the baseline every bid should be compared with. - **Get at least one other bid** from a licensed general contractor. ## The day-one decisions that set the rebuild bill Every square foot torn out during mitigation is a square foot rebuilt later. That's why the first decisions matter so much. | Decision | Remove and replace | Dry in place | | **Drywall** | A "flood cut" above the wet line, commonly at 2 or 4 feet | Clean-water drywall caught quickly can often be dried through small holes or by removing baseboard | | **Cabinets** | Removal, then new cabinets and often new countertops | Remove the toe-kick and dry underneath, or inject dry air into cavities | | **Hardwood floors** | Tear out and replace, often across several rooms to match | Drying mats that pull moisture up through the boards | | **Carpet** | Pad is usually replaced; carpet is often replaced | Carpet itself can sometimes be dried and cleaned after a clean-water leak | | **Insulation** | Soaked insulation is usually removed | Rarely dried in place | **The incentive on both sides:** a company that expects the rebuild has a reason to tear out more, because more removal means a larger second job. A company paid only for drying under tight program targets may remove too little, which can leave hidden moisture and mold. Neither is a reason to distrust everyone. It's a reason to ask, before anything is removed: "Can this be dried in place, and if not, why?" The answer depends on the water category, the material and how long it's been wet. Contaminated water and swollen particleboard usually mean removal. Clean water caught within a day or two often doesn't. Ask for photos and moisture readings of anything removed. They'll matter for the insurance estimate too. ## The matching problem Replace a few rows of flooring in a kitchen that runs into the dining room and hallway, and the new section may not match. The same goes for cabinets, countertops, tile and siding. Who pays to make the whole area match is one of the most argued points in reconstruction. - **Some states' claim-handling rules address matching.** Ohio's rules, for example, call for a reasonably uniform appearance when replacement items can't match in quality, color and size. - **Some policies address it directly,** either way. - **Ask your adjuster in writing** how they'll handle continuous flooring or cabinets that can't be matched, before the rebuild is priced. Drying in place avoids the matching problem entirely, one more reason to ask the question on day one. ## Supplements, code upgrades and the hidden-damage surprise - **Supplements are normal.** When walls open up, contractors often find more damage than the first estimate assumed. They submit a supplement to the insurer with photos. Ask that you're copied on each one. - **Code upgrades may be required.** If the rebuild must meet current building codes, such as new electrical requirements, the extra cost may fall under your policy's ordinance or law coverage, which is often limited. Check yours. - **Permits take time.** Ask who pulls them and whether the timeline includes inspections. ## Following the money - **Separate payments are common:** one for mitigation, one or more for the rebuild, one for contents. - **Your mortgage lender is often named on dwelling checks.** For larger claims, lenders commonly deposit the funds and release them in stages, sometimes after inspections. Contact the lender's loss draft or insurance claims department early to learn its process. - **Depreciation may be withheld** until repairs are finished. Ask what's needed to release it and by when. - **Pay contractors as work is completed,** not far ahead of it, and get lien waivers from the general contractor and major subcontractors as you pay. ## If you have to move out If the house can't be lived in during repairs, your policy's **additional living expenses** coverage, sometimes called loss of use, usually pays the extra cost of living elsewhere: rent or hotel, extra mileage, extra food costs. Keep receipts, and ask your adjuster about limits and how long it lasts, because a slow rebuild uses it up. ## A simple way to decide - **Let mitigation finish properly.** Get the final moisture readings. See is it actually dry. - **Get the insurer's repair estimate** and read it room by room. See how estimates are priced. - **Ask the drying company for a rebuild bid** if you like their work, and get at least one more from a licensed general contractor. - **Compare scope, not just totals:** materials, matching, permits, timeline and warranty. - **Check the license** your state or city requires for reconstruction. ## State rules Contractor licensing, claim-handling and matching rules vary by state. Each state section covers its own: Alabama, Arkansas, Georgia, Illinois, Indiana, Iowa, Kansas, Kentucky, Maryland, Michigan, Minnesota, Mississippi, Missouri, Nebraska, New York, North Carolina, Ohio, Oklahoma, Pennsylvania, South Carolina, Tennessee, Texas, Virginia, West Virginia, Wisconsin. ## Frequently asked questions **What's the difference between water mitigation and restoration?** Mitigation is the emergency phase: stopping the water, extracting it, removing materials that can't be saved and drying the structure. Restoration or reconstruction is the repair phase: replacing drywall, insulation, flooring, cabinets and paint. They're usually separate estimates, and often separate contracts. **Do I have to use the same company for mitigation and the rebuild?** No. You can hire a different licensed contractor for the rebuild. Check your mitigation paperwork for language that commits you to reconstruction, and don't sign a rebuild contract until you've seen the insurer's repair estimate and compared bids. **Can cabinets be dried without removing them?** Often. Technicians can remove the toe-kick at the bottom of the cabinets and force dry air underneath, or use injection drying systems. Whether it works depends on the cabinet material, the water category and how long it was wet. Particleboard that has swollen usually can't be saved. **What does the insurance company pay if new flooring won't match the rest?** It depends on your policy and your state. Some states have claim-handling rules that require a reasonably uniform appearance when replaced items can't match, and some policies address matching directly. Ask your adjuster in writing how they'll handle continuous flooring or cabinets that can't be matched. **Why is the insurance check made out to my mortgage company too?** Your lender has a financial interest in the house, so dwelling payments are often made out to both of you. For larger claims, lenders commonly hold the money and release it in stages as repairs progress and are inspected. Contact the lender's loss draft or insurance claims department as soon as you open a claim. ## Sources - IICRC: ANSI/IICRC S500 Standard for Professional Water Damage Restoration - NAIC: Consumer guide to homeowners insurance - Insurance Information Institute: Understanding the insurance claims payment process - FTC: How to avoid a home improvement scam --- Guide · Inside the industry # Is your house actually dry? Moisture meters, thermal cameras and the drying goal, explained from the inside Walls feel dry long before they are. The decision to pull the fans out, or keep them running another two days, is the most consequential call on a water job, and it rests on a few numbers most homeowners never see. Here's how to read them. The short answer - **Under the IICRC S500 standard, a material is dry when it reaches its drying goal:** a reading close to the same material in an unaffected part of the house, called the dry standard. - **Thermal cameras don't detect water.** They show surface temperature. Wet areas often look cooler because of evaporation, but every cool spot needs a moisture meter to confirm it. - **Meter numbers aren't universal percentages.** On drywall and many other materials, readings are on a relative scale specific to the meter. Compare readings from the same meter at the same marked spots over time. - **Two opposite problems happen:** drying stretched past the goal to bill more equipment days, and drying cut short to keep job costs down. Both show up in the moisture log. - **Before the equipment leaves,** ask for final readings at every monitoring point next to the dry standard, in writing. It protects your claim and your house. ## Dry is a number, not a feeling The paint on a soaked wall can feel dry the next afternoon. The drywall core behind it, the bottom plate of the wall, the subfloor under the vinyl and the insulation in the cavity can stay wet for days. That's where mold starts, usually out of sight, often weeks after everyone has forgotten the leak. So professionals don't decide by touch. Under the **IICRC S500** standard, the industry's reference for water damage restoration, drying is measured, recorded and compared against a target. Understanding that target is the most useful thing a homeowner can learn about a water job. ## The dry standard and the drying goal On the first visit, a technician should do two things: - **Take reference readings** from the same kinds of material in a part of the house the water didn't reach: drywall in a dry room, the same flooring elsewhere, framing on the other side of the house. That's the **dry standard**. - **Mark monitoring points** in the wet area, often with a small numbered sticker or a sketch, and record a reading at each one, every visit, at the same spot. The **drying goal** is a reading at or close to the dry standard. When every monitoring point reaches it, the materials are dry and the equipment can come out. Everything else in this guide depends on those two steps having been done properly. ## The tools, and what each one really tells you | Tool | What it measures | What it can't tell you | | **Thermal (infrared) camera** | Surface temperature. Wet areas often appear cooler because water is evaporating. | Whether a cool spot is water. Drafts, missing insulation, ducts and outside walls look similar. It can't see through materials. | | **Pin meter** | Electrical resistance between two pins pushed into the material, at the depth of the pins | Anything deeper than the pins. Readings outside wood are relative, not true moisture percentages. | | **Pinless meter** | Changes in an electrical field through the surface, a short distance into the material | A true percentage. Readings shift with material density, and nearby metal such as nails, foil backing or wiring can throw them off. | | **Thermo-hygrometer** | Air temperature and relative humidity, used to calculate grains per pound (GPP), the actual amount of water in the air | Anything about materials directly. It tells you whether the drying conditions are working. | | **Concrete testing** | Moisture in slabs, using probes or specialized meters | A quick answer. Concrete dries slowly, and flooring manufacturers set their own limits. | **The thermal camera as a sales prop:** a colorful thermal image of "water inside your walls" is persuasive, and sometimes it's right. But a camera alone proves nothing. If someone shows you a thermal image as the reason to open a wall, ask to see a moisture meter reading at that same spot first. ## Why the numbers don't travel Most homeowners assume a reading of "18" means 18% moisture. On wood, with a meter set for wood, it roughly does: wood moisture content is a real percentage, and indoor framing typically settles somewhere below about 15% when dry. On drywall, plaster, concrete and most other materials, many meters show a **relative scale** that only means something compared with other readings from the same meter. Three practical consequences: - **You can't compare two companies' readings** if they used different meters or settings. - **A single number without a dry standard beside it means very little.** Always ask, "And what does the dry wall read?" - **Trends matter more than values.** Readings at the same point should fall day by day and then level off near the dry standard. ## Reading the air: is the equipment working? A good drying log records the air too: inside the affected area, in an unaffected room, outside, and at the dehumidifier's exhaust. The key figure is **GPP**, grains of water per pound of dry air. - **The dehumidifier's exhaust should read well below the room's GPP.** If it doesn't, the machine isn't pulling water out of the air. - **The room's GPP should drop** over the first day or two. - **Cold matters.** Common refrigerant dehumidifiers lose capacity in cold rooms, which is why a basement in winter may need heat or a desiccant dehumidifier instead. ## Problem one: drying that's stretched Every machine bills every day. That creates a temptation to leave equipment running after the materials are dry. Signs in the log: - Readings reached the dry standard, but the equipment stayed another day or two "to be safe." - Identical numbers copied from day to day. Real readings wander a little. - Monitoring visits billed on days with no readings recorded. - Equipment counts that stayed the same while the wet area shrank. A reasonable margin is normal. Several days past the goal isn't, and it's one of the most common disputes in mitigation billing. ## Problem two: drying that's cut short The opposite problem gets less attention and causes more damage. Insurers and the administrators who run their vendor programs often track measures like average drying days and average job cost, and companies that work in those programs feel pressure to keep both down. Busy companies after a storm also want their equipment back for the next job. Drying cut short tends to look like this: - Final readings only on surfaces you can see, none inside wall cavities, under flooring or behind cabinets. - No final reading at some monitoring points at all. - Equipment pulled on a fixed day, such as day three, regardless of readings. - Baseboards and drywall reinstalled before the wall's bottom plate was checked. The result shows up weeks later as a musty smell, swollen baseboard or mold at the bottom of a wall. By then, the claim is closed. ## Hidden places that need a reading - **The bottom 2 feet of walls,** including the wood plate the wall sits on - **Under cabinets,** reached through the toe-kick at the bottom - **The subfloor** under hardwood, tile, laminate or vinyl, from below if there's a basement or crawl space - **Insulation** inside exterior walls and ceilings, which holds water and is usually replaced if soaked - **The ceiling below** a second-floor leak ## What you can do yourself - **Ask for the moisture map on day one:** where the monitoring points are and what the dry standard is for each material. - **Photograph the meter display** at a few points when the technician takes readings. It takes seconds. - **Ask on day two or three,** "Which points are still above the goal, and what's the plan for them?" - **Consider an inexpensive pin meter** to watch trends at the same spots and to check hidden areas later. Use it for direction, not for arguing numbers. - **Get the final readings in writing** before the equipment leaves: every point, beside its dry standard, with the date. ## Before you reinstall flooring Flooring manufacturers set their own moisture limits for subfloors and slabs, and many warranties depend on them. Hardwood that has cupped may flatten as it dries, so replacing it too early can be a costly mistake. Before new flooring goes down, ask the installer to test the subfloor or slab against the manufacturer's limit and record the result. ## Why the final log matters later Keep the final drying report with your claim file and your house records. It's the evidence that the house was properly dried if mold appears months later, if an insurer questions a later claim, or if a buyer's inspector finds old water staining when you sell. ## State claim rules Each state section covers its claim rules and insurance regulator: Alabama, Arkansas, Georgia, Illinois, Indiana, Iowa, Kansas, Kentucky, Maryland, Michigan, Minnesota, Mississippi, Missouri, Nebraska, New York, North Carolina, Ohio, Oklahoma, Pennsylvania, South Carolina, Tennessee, Texas, Virginia, West Virginia, Wisconsin. ## Frequently asked questions **How do restoration companies know when walls are dry?** They take reference readings from the same kind of material in an unaffected room (the dry standard), then take readings at marked points in the wet area every day. When the wet area's readings reach the drying goal, close to the dry standard, the material is considered dry under the IICRC S500 standard. **Can a thermal camera see water behind a wall?** Not directly. A thermal camera shows surface temperature. Wet materials often look cooler because water is evaporating, but drafts, missing insulation and ductwork can look the same. A moisture meter is needed to confirm whether a cool area is actually wet. **What moisture reading is considered dry for drywall?** There isn't one universal number, because many meters read drywall on a relative scale. The meaningful comparison is between the wet area and the same material in a dry area, measured with the same meter. Wood is different: wood moisture content is a true percentage, and indoor framing is commonly around 15% or lower when dry. **Should I buy my own moisture meter?** An inexpensive pin meter can be useful for watching trends at the same spots day to day and for checking hidden areas after the equipment leaves. Don't compare its numbers directly with a contractor's meter. Different meters, settings and scales give different readings. **Why did mold show up after the restoration company said it was dry?** Usually because something wasn't measured: a wall cavity, the subfloor under hardwood or tile, the back of a cabinet, or insulation. Surfaces can read dry while materials behind them stay wet. Final readings should include those hidden spots. ## Sources - IICRC: ANSI/IICRC S500 Standard for Professional Water Damage Restoration - U.S. EPA: A Brief Guide to Mold, Moisture and Your Home - USDA Forest Products Laboratory: Wood Handbook, moisture relations - U.S. EPA: Mold Remediation in Schools and Commercial Buildings --- Guide · Damage # Found mold after a leak: is it safe to sleep in that room tonight? You moved the bed and found black spots on the wall, or a leak left a musty patch in a child's room. It's late, everyone's worried, and the internet is full of 'toxic mold' scare stories. Here's what the health agencies actually say, and a sensible plan for tonight. The short answer - **For most healthy adults, one more night near a small patch of mold is unlikely to cause lasting harm.** Mold mainly causes allergy-type and breathing symptoms, which are worse with more exposure. - **Sleep somewhere else if** anyone in that room has asthma, allergies, a weakened immune system or chronic lung disease, if the patch is large, if it followed sewage or floodwater, or if the room smells strongly musty. - **Color doesn't decide danger.** The CDC says you don't need to identify the type of mold; all mold should be removed and the moisture fixed. - **Testing is usually unnecessary.** The EPA says if you can see or smell mold, sampling usually isn't needed, and there are no federal limits to compare results against. - **Size decides who cleans it:** under about 10 square feet, usually you; larger, in walls or ducts, or after dirty water, a professional. ## What mold actually does to health The CDC describes mold's main effects as **allergy and breathing symptoms**: a stuffy nose, wheezing, and red or itchy eyes or skin. People with **asthma** or **mold allergies** can react more strongly, and people with **weakened immune systems** or **chronic lung disease** are at higher risk of infections. Exposure matters: more mold and longer time in the room means more chance of symptoms. That's why the answer to "is it safe tonight?" depends on **who** is sleeping there and **how much** mold there is, not on its color. ## Tonight: a quick decision | Sleep elsewhere tonight if… | Staying one more night is usually reasonable if… | | Anyone in the room has asthma, allergies, a weakened immune system or chronic lung disease | Healthy adults only | | The visible mold is larger than about 10 square feet | A small patch you can see the edges of | | It followed sewage or floodwater | It followed a clean-water leak | | A strong musty smell fills the room, or the wall or ceiling is still wet or sagging | Faint or no smell, surfaces dry | | Someone is already having symptoms | No one has symptoms | Many families also choose to move babies and older relatives out until cleanup is done. That's a reasonable, low-cost precaution. ## If you stay in the room tonight - **Don't disturb it.** Scrubbing, scraping or dry-brushing releases spores. Leave it for tomorrow's proper cleanup. - **Cover a small patch** loosely with plastic sheeting and painter's tape if you can do it without rubbing the surface. - **Move the bed** away from the affected wall. - **Ventilate** if the outdoor air is dry, and keep the door to the rest of the house closed. - **Don't run the central heating or air conditioning** if you suspect mold in the ducts or air handler. ## Do you need a mold test? Usually not. The EPA says that if you can **see or smell mold**, sampling is usually unnecessary, and there are **no EPA or federal limits** for mold to compare results against. The CDC agrees you don't need to know the species: **remove it and fix the moisture**. Testing is useful in specific situations, like finding a hidden source when you smell mold but can't see it, or checking a remediation, and should be done by a qualified professional. Be wary of anyone who offers to test and remediate and uses scary results to sell the job. The size of the visible damage and the moisture source matter more than a lab report. ## The next 48 hours - **Find and stop the water.** Mold always has a moisture source: the leak you found, condensation, or a damp wall. Cleaning without fixing it means it comes back. See hidden water damage. - **Photograph it** with something for scale, for your records and any insurance claim. Mold coverage is often limited; see what insurance covers. - **Small, from clean water, no vulnerable people?** Clean it yourself: detergent and water on hard surfaces, gloves, goggles and an N95. Porous materials like drywall, ceiling tiles and carpet with mold usually have to be removed. The EPA doesn't recommend bleach as a routine fix. - **Larger, inside walls, in ducts, or after dirty water?** Call a professional. Remediation under the IICRC S520 standard seals off the area so spores don't spread during removal. - **Dry everything** within 24 to 48 hours of any new wetting, and keep indoor humidity low. ## When to see a doctor If anyone has wheezing, trouble breathing, worsening asthma or symptoms that don't settle after leaving the room, contact a doctor. Tell them about the mold. For a medical emergency, call 911. ## Get it cleaned up properly Local restoration and mold remediation help is listed in each state section, along with that state's insurance and contractor rules: Alabama, Arkansas, Georgia, Illinois, Indiana, Iowa, Kansas, Kentucky, Maryland, Michigan, Minnesota, Mississippi, Missouri, Nebraska, New York, North Carolina, Ohio, Oklahoma, Pennsylvania, South Carolina, Tennessee, Texas, Virginia, West Virginia, Wisconsin. ## Frequently asked questions **Is it safe to sleep in a room with mold?** For a healthy adult and a small, recent patch, usually yes for a night or two while you arrange cleanup, especially with the patch covered and the room ventilated. Anyone with asthma, allergies, a weakened immune system or chronic lung disease should sleep elsewhere until it's cleaned up, and so should everyone if the area is large or followed sewage or floodwater. **Is black mold more dangerous than other mold?** Color isn't a reliable guide to risk. The CDC says it's not necessary to determine what type of mold you have; all mold should be treated the same way, by removing it and fixing the moisture problem. **Should I get a mold test?** Usually not. The EPA says that if visible mold is present, sampling is usually unnecessary, and there are no EPA or federal limits for mold to compare results against. Testing can help in specific cases, such as tracking down a hidden source or checking cleanup, done by a qualified professional. **What are symptoms of mold exposure?** According to the CDC, mold can cause a stuffy nose, wheezing, and red or itchy eyes or skin. People with asthma or mold allergies can have stronger reactions, and people with weakened immune systems or chronic lung disease are at higher risk of infections. See a doctor if symptoms are significant or persistent. **Can I clean the mold myself?** The EPA's rule of thumb is that a homeowner can usually handle an area under about 10 square feet if it's from clean water and no one in the home is especially vulnerable. Use detergent and water on hard surfaces, wear gloves, goggles and an N95, and don't use bleach as a routine fix. Larger areas, mold inside walls or ducts, or mold after sewage call for a professional. ## Sources - CDC: Mold, about mold and health - U.S. EPA: A Brief Guide to Mold, Moisture and Your Home - U.S. EPA: Mold testing or sampling - U.S. EPA: Should I use bleach to clean up mold? - IICRC: ANSI/IICRC S520 Standard for Professional Mold Remediation --- Guide · Inside the industry # Mold testing and remediation: the conflicts of interest, scare tactics and upsells to know before you pay Mold is the part of this industry where fear sells most easily. The test results are hard to read, the health claims are frightening, and the person interpreting both is often the person who'll be paid to fix it. Here's how to separate the diagnosis from the sale. The short answer - **The core conflict:** when the company that tests for mold also removes it, the test decides the size of its own job. Texas and New York prohibit the same licensee from doing both on one job. Elsewhere, you can separate them yourself. - **The EPA says there are no federal standards for acceptable mold levels,** and that if you can see or smell mold, sampling usually isn't needed. The job is to fix the moisture and remove the growth. - **Fogging, ozone and painting over mold don't remove it.** The EPA advises against painting or caulking moldy surfaces and says ozone at safe levels isn't effective against indoor pollutants. - **A real remediation follows a written scope:** fix the water source, contain the area, remove damaged porous materials, HEPA-vacuum and clean, dry, then verify the result against criteria agreed before work started. - **Clearance should be judged by someone with no stake in the result,** using the goal in the IICRC S520 standard: a return to normal background conditions, not zero spores. ## The conflict at the center of mold work Mold jobs are priced by scope: how many square feet, how many rooms, how much containment, how much material comes out. Whoever defines that scope controls the price. In many mold jobs, the same company inspects, tests, reads the lab report, writes the scope and then does the removal. Two of the states we cover treat that as a conflict serious enough to regulate: - **Texas** licenses mold assessors and mold remediators separately through the Texas Department of Licensing and Regulation, and a licensee can't perform both the assessment and the remediation on the same project. - **New York** licenses mold assessors, remediation contractors and abatement workers under Article 32 of its Labor Law, which bars a licensee from performing both assessment and remediation on the same property, and bars anyone from owning an interest in both companies on that property. Most other states have no mold licensing at all. That doesn't make the conflict go away. It just means you have to separate the roles yourself: one company, paid a flat fee with no stake in the size of the job, to assess; another to remediate. ## What mold tests can and can't tell you There are **no federal standards for acceptable levels of mold** indoors. The EPA's guidance is direct: if you can see or smell mold, you have a problem to fix, and sampling usually isn't necessary. That's worth knowing before you pay for a test. | Test | What it shows | Limits | | **Air sample (spore trap)** | Spores in the air at that moment, by type, compared with an outdoor sample | A snapshot. Counts swing with weather, activity and time of day. Without an outdoor comparison, the number means little. | | **Surface sample (tape or swab)** | Whether a stain is mold, and roughly what kind | Says nothing about how far growth extends | | **Wall cavity sample** | Air inside a closed wall | Useful for tracing hidden growth, easy to over-interpret | | **ERMI and similar DNA dust tests** | Mold DNA in settled dust | Developed as a research tool. The EPA has said it isn't validated for routine use in homes. | | **Moisture readings** | Where materials are wet now | Often more useful than any spore test, because moisture is what grows mold | Testing does have real uses: tracing a musty smell with no visible source, documenting a condition for an insurance or landlord dispute, and verifying that remediation worked. It's least useful as the opening move of a sales visit. ## Scare tactics to recognize - **"Toxic black mold."** Color doesn't identify the species or the risk. The CDC and EPA treat all indoor mold growth the same way. See black mold. - **A lab report with red bars and no outdoor comparison.** Indoor counts mean little until they're compared with outdoor air on the same day. - **"Your whole house is contaminated"** after a small leak in one room, without moisture readings to show where the water went. - **"You need to leave tonight"** for a small patch of growth in a basement. Who should take extra care is covered in safe to sleep. - **Health diagnoses from a contractor.** Mold can trigger allergies and asthma, and people with weakened immune systems face more risk. Medical questions belong with a doctor. ## Treatments that don't remove mold Mold, living or dead, can cause allergic reactions. That's why every credible guideline, from the EPA to the IICRC S520 standard, comes down to **physical removal** plus fixing the moisture. Be skeptical of any of these sold as the fix: | Upsell | The problem | | **Fogging with a biocide** | Can kill surface mold but leaves it in place, and doesn't reach growth inside materials | | **Ozone treatment** | The EPA says ozone at safe levels isn't effective against indoor pollutants, and higher levels irritate the lungs. It doesn't remove mold. | | **Painting over growth** with "mold-killing" primer | The EPA advises against painting or caulking moldy surfaces. Sealers belong on cleaned framing after removal. | | **Air scrubbers alone** | HEPA air filtration is part of a remediation, not a replacement for removing the source | | **Whole-house duct cleaning** | Sometimes needed, but only when growth or contamination in the ducts has been found, not as a standard add-on | ## What a real remediation includes Ask for a written **scope of work**, often called a protocol, before work starts. It should cover: - **The moisture source and how it's being fixed.** Without this, the mold returns. - **The affected area,** with measurements and photos. - **Containment** sized to the job: plastic barriers and negative air pressure so spores don't spread to the rest of the house. The EPA's guidance scales precautions with the size of the area: under about 10 square feet is often manageable by a careful homeowner, while larger areas call for more protection. - **Removal of damaged porous materials,** like drywall, insulation and carpet, bagged inside the containment. - **Cleaning of what stays:** HEPA vacuuming, then damp wiping, and sanding where growth is on framing. - **Drying,** confirmed with moisture readings. See is it actually dry. - **Verification** against criteria written down in advance. ## Clearance: what "done" should mean The IICRC S520 standard describes three conditions. Condition 1 is normal background mold, the kind every house has. Condition 2 is settled spores from nearby growth. Condition 3 is actual growth. The goal of remediation is to return the area to **Condition 1**, not to zero spores, which isn't achievable anywhere. Verification usually means a visual inspection, moisture readings and sometimes sampling. It's most credible when done by someone who isn't being paid by the remediation company, against standards agreed before work started. If you hired an independent assessor, have them do the clearance too. ## Pricing tells - **A price per square foot of "affected area"** where the area was defined by the same company's test. - **A scope that grows once walls are open.** Sometimes that's legitimate, because hidden growth is common. Ask for photos and a written change order before more work is done. - **A low price with no containment,** which may spread spores into clean rooms. - **Long-term "maintenance treatments"** sold as a subscription. ## The insurance angle Many homeowners policies exclude mold or cap it with a **sublimit**, often a few thousand dollars and sometimes up to about $10,000, even when the water damage that caused it is covered. Read your policy's mold language before agreeing to a large scope, and see what insurance covers. Mold caused by a recent, covered leak is usually handled as part of that water claim, so report it as early as possible. ## Questions to ask before you hire **For the assessor:** - Do you also do remediation? If so, will you step aside on this project? - Will you take an outdoor comparison sample and moisture readings? - Will you write a protocol that any remediation company can bid on? **For the remediator:** - Are your technicians trained to the IICRC S520 standard? - How will you contain the area and protect the rest of the house? - What exactly will you remove, and what will you clean and leave? - What are the clearance criteria, and who checks them? - Do you hold the license your state requires, if any? ## State rules Licensing, disclosure and insurance rules differ by state. Each state section covers its own: Alabama, Arkansas, Georgia, Illinois, Indiana, Iowa, Kansas, Kentucky, Maryland, Michigan, Minnesota, Mississippi, Missouri, Nebraska, New York, North Carolina, Ohio, Oklahoma, Pennsylvania, South Carolina, Tennessee, Texas, Virginia, West Virginia, Wisconsin. ## Frequently asked questions **Should the same company test for mold and remove it?** Ideally not. The company that interprets the test sets the scope of the removal it will be paid for. Texas and New York prohibit the same licensee from performing both the assessment and the remediation on the same job. In other states it's allowed, but hiring an independent assessor avoids the conflict. **Do I need a mold test?** Often not. The EPA says that if visible mold is present, sampling is usually unnecessary, and there are no federal limits for mold levels to compare results against. Testing can help in specific cases, such as tracing a smell with no visible source, a dispute, or confirming a remediation was successful. **Does fogging or ozone kill mold?** Neither removes mold. Dead mold can still cause allergic reactions, so the growth has to be physically removed. The EPA says ozone generators are not effective at removing indoor air pollutants at concentrations that don't exceed health standards, and ozone itself irritates the lungs. **Can mold be painted over with a special primer?** Not as a fix. The EPA advises against painting or caulking moldy surfaces. Encapsulating sealers are sometimes used on cleaned framing after removal, as a final step, not instead of removal. **Is black mold more dangerous than other mold?** Color doesn't tell you the species or the risk. The CDC and EPA treat all indoor mold growth the same way: fix the moisture and remove it. See our black mold guide for more. **What is post-remediation verification?** A check after the work is done to confirm the remediation met its goal. It usually includes a visual inspection, moisture readings and sometimes sampling. It's most credible when done by someone independent of the remediation company, against criteria written down before work started. ## Sources - U.S. EPA: A Brief Guide to Mold, Moisture and Your Home - U.S. EPA: Mold Remediation in Schools and Commercial Buildings - U.S. EPA: Ozone generators that are sold as air cleaners - CDC: Mold - IICRC: ANSI/IICRC S520 Standard for Professional Mold Remediation - Texas Department of Licensing and Regulation: Mold assessors and remediators FAQ - New York Labor Law Section 936: Mold licensing and prohibited conflicts --- Guide · Insurance # The restoration company wants a signature: work authorization, direction to pay or assignment of benefits? The crew is in your driveway, the floor is wet, and a tablet appears with 'just sign here'. Most of these documents are routine. One kind hands your insurance claim to the contractor. Two minutes of reading tells you which you're holding. The short answer - **A work authorization** is permission to start work and an agreement to pay. It's normal and usually required. - **A direction to pay** lets your insurer pay the company directly, while you keep control of your claim. - **An assignment of benefits (AOB)** transfers some of your rights under the policy to the contractor, which may let them deal with, or sue, your insurer over the claim. It's a much bigger decision. Florida banned AOBs for policies issued from January 1, 2023. - **Read five things before signing:** how the price is set, what you owe if insurance doesn't pay, cancellation terms, liens, and anything that assigns benefits. - **The FTC Cooling-Off Rule** generally gives you 3 business days to cancel sales made at your home, but there's an emergency exception you can waive in writing. Know whether you're waiving it. ## Three documents that look alike | Document | What it does | Who controls the claim | How careful to be | | **Work authorization** | Permission to start and an agreement to pay for the work | You | Normal; read the payment terms | | **Direction to pay** | Tells your insurer to pay the company directly | You | Usually fine; confirm it doesn't also assign rights | | **Assignment of benefits (AOB)** | Transfers some of your policy rights for this loss to the company | Partly the company | Slow down; you can usually say no and still get the work | The title on the page isn't always reliable. A document called "Work Authorization" can contain assignment language in the small print. Look for words like assign, assignment, transfer or all rights and benefits. ## Five things to read before you sign anything - **How the price is set.** Is there an estimate, an hourly rate, or "pricing per the current industry estimating software"? Ask for an itemized estimate as soon as the scope is clear. - **What you owe if insurance doesn't pay.** Most contracts make you responsible for anything the insurer doesn't cover, plus your deductible. That's common; just know it. - **Cancellation.** How do you stop the work, and what do you pay for work already done and equipment already placed? - **Liens.** Contractors can often file a lien on your property if they aren't paid. Check what the contract says about disputes before it gets there. - **Assignment language.** If you see it, you can ask for a version without it, strike it before signing, or ask whether a direction to pay will do instead. ## Your right to cancel The FTC's **Cooling-Off Rule** generally gives you **three business days to cancel** a sale of $25 or more made at your home, and requires the seller to tell you about that right. But it has an **emergency exception**: if you need goods or services to meet a genuine emergency, you request them, and you sign a **separate, dated statement in your own words** describing the emergency and waiving the right to cancel, the three-day right doesn't apply. That's exactly the situation after a burst pipe. If a company asks you to sign an emergency waiver, it may be legitimate, but read it and keep a copy. Some states add their own home-solicitation or contractor rules; your state section on this site lists them. ## About assignments of benefits An AOB can be convenient: the company deals with the insurer, and you're not chasing payments. The trade-off is control. Depending on your state and the document, the contractor may negotiate, dispute, or even sue over that part of your claim, and you may have less say. Rules vary a lot by state. **Florida** prohibited assignment of post-loss benefits under residential and commercial property policies issued on or after **January 1, 2023**, after years of disputes and litigation. Other states allow AOBs, sometimes with required disclosures or cancellation rights. If you're unsure, call your state insurance department's consumer line before signing. ## A calm way to handle the tablet in the driveway - Say: "I'm happy to authorize emergency drying. Can I read this first?" Reputable companies expect that. - Ask: "Is there anything in here that assigns my insurance benefits to you?" - If yes, ask whether a **direction to pay** will do instead. - Photograph or download a copy of everything you sign. - If you feel pressured, it's fine to let them start **emergency extraction only** under a simple authorization and decide on the rest once you've talked to your insurer. ## Find a restoration company near you Each state section covers that state's contractor and cancellation rules, with county pages for local help: Alabama, Arkansas, Georgia, Illinois, Indiana, Iowa, Kansas, Kentucky, Maryland, Michigan, Minnesota, Mississippi, Missouri, Nebraska, New York, North Carolina, Ohio, Oklahoma, Pennsylvania, South Carolina, Tennessee, Texas, Virginia, West Virginia, Wisconsin. ## Frequently asked questions **Do I have to sign a work authorization for water mitigation?** Usually yes. A restoration company needs written permission to enter, remove materials and set up equipment, and an agreement about payment. That's normal. What matters is what else the document contains. **What is an assignment of benefits in water damage?** An assignment of benefits transfers some of your rights under your insurance policy for that loss to the contractor. The contractor can then seek payment from your insurer directly and, depending on state law and the document, pursue disputes over the claim. You may lose some control over how that part of your claim is handled. **Are assignments of benefits legal?** It depends on the state. Florida prohibited assignment of post-loss benefits under residential and commercial property insurance policies issued on or after January 1, 2023. Other states allow them, sometimes with consumer protections. Your state insurance department can tell you the current rules. **Can I cancel a restoration contract after signing?** Often, within limits. The FTC Cooling-Off Rule generally gives you three business days to cancel sales made at your home, but it has an exception for bona fide emergencies where you request the work and sign a separate, dated statement waiving the right. Some states add their own rules. Check what you signed and ask the company in writing. **What's the difference between a direction to pay and an assignment of benefits?** A direction to pay only tells your insurer to pay the contractor directly for the work. You keep your rights and control of the claim. An assignment of benefits transfers rights to the contractor. ## Sources - FTC: Buyer's remorse, the FTC's Cooling-Off Rule - eCFR: 16 CFR Part 429, Cooling-Off Rule (including the emergency exception) - Florida Senate: SB 2-A (2022), property insurance reforms including assignment of benefits - NAIC: Find your state insurance department --- Guide · Emergency # Roof leaking into the house: what to do right now Water through the ceiling during a storm is frightening, but most of what you can do happens inside. Stay off the roof until the storm passes, and focus on the ceiling and what's under it. The short answer - Don't go on the roof during rain, wind or lightning. The emergency work is inside: turn off power to ceiling lights and fans near the leak, move belongings, and catch the water. - If the ceiling is bulging with water, keep people out from under it, set a bucket below, and puncture the low point of the bulge with a screwdriver to drain it in a controlled way. A waterlogged ceiling can collapse. - After the storm, a roofer or restoration company can put a tarp over the damaged area. Insurance policies expect you to make reasonable temporary repairs, so keep receipts. - Wet ceiling drywall and attic insulation usually have to come out, and attic framing needs to dry within a day or two to prevent mold. - Sudden storm damage is usually covered by homeowners insurance. Leaks from an old or worn roof usually aren't. ## While it's still raining - **Make it safe.** If water is dripping near a light fixture, ceiling fan or outlet, switch off that circuit at the breaker panel, as long as you can reach the panel without standing in water. - **Clear the area.** Move furniture, electronics and rugs out from under the leak, and cover what you can't move with plastic sheeting. - **Catch the water.** Buckets, trash cans and towels. Lay a towel inside the bucket to stop splashing. - **Relieve a bulging ceiling.** If water is pooling above the drywall, puncture the low point of the bulge with a screwdriver over a bucket, standing to the side. If it's sagging or cracking, keep everyone out of the room. - **Check the attic** if you can get there safely. Put a board across the joists and a bucket under the drip, and pull wet insulation away from the ceiling. ## After the storm - **Look from the ground first.** Use binoculars to spot missing shingles, damaged flashing around the chimney and vents, or debris on the roof. - **Get the roof covered.** A tarp secured well past the damaged area keeps the next rain out. Emergency tarping is a reasonable temporary repair your insurer should expect. - **Dry the inside.** Wet attic insulation usually has to be removed. Ceiling drywall that sagged or stained deeply usually comes out too. Attic framing and roof sheathing need to dry quickly to prevent mold and rot. ## Document for insurance - Video and photos of the ceiling, walls, floors and damaged belongings, and of the roof from the ground. - The date and time the leak started and the weather that day. Local storm reports can support a wind or hail claim. - Receipts for tarps, buckets, fans, emergency services and any hotel stay. - Don't throw away damaged shingles or belongings until the adjuster has seen them or approved disposal. ## Common roof leak sources | Source | Clue | | Missing or lifted shingles | Leak after high wind; shingles in the yard | | Flashing at chimneys, walls and skylights | Stain near a chimney or skylight; leak in wind-driven rain | | Plumbing vent boots | Stain on a bathroom or kitchen ceiling below a vent pipe | | Ice dams | Leak at exterior walls in winter, during a thaw | | Clogged gutters | Water at the top of exterior walls or soffits during heavy rain | | Attic condensation | Damp sheathing and frost in winter with no rain; poor attic ventilation | ## Frequently asked questions **Should I poke a hole in a ceiling that's bulging with water?** If the bulge is filling with water and there's no light fixture or wiring in it, yes: it's safer to drain it into a bucket than to let it collapse. Turn off power to that area first, stand to the side, and use a screwdriver at the low point of the bulge. If the ceiling is sagging badly or cracking, keep everyone out of the room instead. **Can I tarp my own roof?** Only when the weather has cleared, the roof is dry and not steep, and you can do it safely with someone else present. Falls from roofs cause serious injuries. Many roofers and restoration companies offer emergency tarping, and the cost is often part of an insurance claim. **Why does my ceiling leak only when it rains hard or the wind blows?** Wind-driven rain can get under damaged shingles, flashing around chimneys, vents and skylights, or through gaps at the roof edge that stay dry in calm rain. A leak far from where the water shows up is common, because water runs along rafters and the top of the ceiling before it drips. **Does insurance cover a leaking roof?** If wind, hail or a fallen tree suddenly damaged the roof, homeowners insurance usually covers the roof repair and the interior water damage after your deductible. If the roof leaked because of age, wear or poor maintenance, the roof itself usually isn't covered, and interior damage may be disputed. ## Sources - Ready.gov: Severe weather and home safety - U.S. EPA: A Brief Guide to Mold, Moisture and Your Home - Insurance Information Institute: Am I covered? --- Guide · Detection # Signs of hidden water damage, and how to find a leak Most of the worst water damage starts small and out of sight: a weeping fitting inside a wall, a wax ring under a toilet, a drip in the attic. Here's how to spot it early. The short answer - Common signs of hidden water damage are a **musty smell**, stains or yellow-brown rings on ceilings and walls, bubbling or peeling paint, warped or soft flooring, loose tiles, and a water bill that rises without explanation. - To check for a plumbing leak, turn off every faucet and water-using appliance and read your water meter, then read it again after two hours. If the number changed, water is going somewhere. - A few drops of food coloring in the toilet tank that show up in the bowl within 10 to 15 minutes, without flushing, mean the flapper is leaking. - Once you find a hidden leak, stop the water, photograph everything, and get a moisture inspection. Hidden leaks are often slow leaks, which many insurance policies don't cover, so act quickly once you know. ## Warning signs, room by room | Where | What to look for | Likely source | | Ceilings | Stains, rings, sagging, peeling paint, drips at light fixtures | Bathroom above, roof, ice dam, attic condensation, HVAC drain line | | Walls | Bubbling paint, soft drywall, swollen baseboards, dark patches near the floor | Supply or drain line in the wall, shower valve, failed caulk or grout | | Floors | Cupped or buckled hardwood, soft spots, lifting vinyl, loose or cracked tile | Toilet wax ring, dishwasher, fridge line, slab or subfloor leak | | Under sinks | Warped cabinet base, stains, damp smell | Supply line, drain trap, faucet, garbage disposal | | Basement and crawl space | Efflorescence (white crust), damp walls, standing water, musty smell | Groundwater, gutters and grading, plumbing above, condensation | | Outside | Constantly wet soil, unusually green patch, water at the foundation | Water service line, irrigation, downspouts | ## The water meter test - **Turn off all water use.** Faucets, showers, the dishwasher, washing machine, ice maker, irrigation and any water softener regeneration. - **Read the meter.** Note the number, and watch the small leak indicator (often a triangle or dial) for movement. - **Wait two hours** without using any water. - **Read it again.** Any change means water is leaving the plumbing. If the meter moves with the main shutoff inside the house closed, the leak may be in the service line between the meter and the house. ## The toilet dye test Toilets are among the most common sources of silent leaks. Put a few drops of food coloring in the tank, wait 10 to 15 minutes without flushing, and look in the bowl. Color in the bowl means the flapper is letting water through. That wastes water but usually doesn't damage the house; a leak at the base of the toilet, a loose supply line or a failed wax ring does. ## Other clues - **The water bill.** A higher bill with no change in use is a classic sign of a hidden leak. - **Sounds.** Running or hissing water when nothing is on, or a pump or well that cycles at night. - **Hot spots on a slab floor.** A warm patch on a concrete floor can point to a hot water line leaking under the slab. - **Pests.** Termites, carpenter ants and silverfish are drawn to damp wood. ## Once you find it - **Stop the water** at the fixture valve or the main. - **Photograph and video** the damage and the source before anything is removed. - **Get a moisture inspection.** Visible damage is usually the smallest part; a moisture map shows how far water spread inside walls and floors. - **Call your insurer** if the damage is significant. Coverage often turns on whether the leak was sudden or long-running, so give the facts and keep the failed part. ## Frequently asked questions **What does water damage in a wall look like?** Look for discolored or darker patches, a yellow or brown ring, paint that bubbles or peels, drywall that feels soft or crumbly when pressed, baseboards that are swollen or pulling away, and a musty odor. Damage often shows near the bottom of the wall or directly below a bathroom or kitchen. **Why does my house smell musty but I can't see water?** A persistent musty or earthy smell usually means mold or mildew is growing somewhere damp, often inside a wall, under flooring, in a crawl space or behind an appliance. Check under sinks, around toilets, behind the washer and refrigerator, and in the basement or crawl space. **Can a professional find a leak without opening walls?** Usually they can narrow it down. Restoration and leak detection companies use moisture meters, thermal imaging cameras and sometimes acoustic tools to locate wet areas and the likely source before cutting a small, targeted opening. **How much water can a small leak waste?** More than most people expect. The EPA's WaterSense program estimates that household leaks can waste nearly 10,000 gallons a year in an average home, and the same slow leak that wastes water can quietly rot subfloors and framing. ## Sources - U.S. EPA WaterSense: Fix a Leak Week - U.S. EPA WaterSense: Home maintenance - U.S. EPA: A Brief Guide to Mold, Moisture and Your Home --- Guide · Damage # Small leak: can you dry it yourself, or do you need a restoration company? Five checks Most small leaks are a towel-and-fan job. Some look small and aren't: the water is under the floor, inside the cabinet base, or behind the wall. These five checks take ten minutes and tell you which kind you have. The short answer - **Usually DIY:** clean water, caught within a few hours, on hard surfaces you can see and reach, a small area, and everything feels dry within a day or two. - **Call a professional:** gray or black water, anything wet for more than 48 hours, water under flooring or inside walls, swollen cabinet bases or subfloor, a musty smell, or ceilings below that got wet. - **The clock matters:** the EPA advises drying wet materials within 24 to 48 hours to prevent mold. - **The EPA's mold rule of thumb:** areas under about 10 square feet can usually be cleaned by a homeowner; larger areas need a professional. - **A cheap moisture meter** from a hardware store removes most of the guesswork about whether something is really dry. ## Fix the leak first Close the fixture's valve or the main shutoff, and fix or replace the failed part before you start drying. Drying around a slow drip is drying forever. See appliance and toilet leaks for the valves and the hoses that fail most. ## The five checks ### 1. What kind of water was it? - **Clean** (a supply line, the sink's cold or hot line, rain through a window): DIY is possible. - **Gray** (dishwasher or washing machine water, a toilet overflow without feces): be more careful; porous materials it soaked often need to go. - **Black** (sewage, toilet with feces, floodwater): **call a professional.** Don't clean it yourself. More detail in clean, gray or black water. ### 2. How long was it wet? The EPA advises drying wet materials within **24 to 48 hours** to prevent mold. A leak you caught within hours is a very different job from one you found under the sink after a week. **Wet for more than 48 hours, or an unknown time? Lean toward a professional assessment.** ### 3. What got wet? | Material | Usually | | Tile, sealed concrete, metal, plastic | Dries well; wipe and ventilate | | Plywood | Often dries well with airflow | | Particleboard or MDF (cabinet bases, some subfloors) | Swells and crumbles; often needs replacing | | Drywall | Wicks water upward; can dry if caught quickly, otherwise the bottom section is cut out | | Carpet and pad | Pad usually needs replacing after soaking; carpet can sometimes be saved if clean water and quick | | Hardwood flooring | Can cup; needs slow, controlled drying, often professional | | Insulation | Wet insulation in walls or ceilings usually has to come out | ### 4. How big is it? The EPA's mold guidance uses about **10 square feet** (roughly 3 feet by 3 feet) as the line below which a homeowner can usually handle cleanup. The same rough size works as a gut check for water: a wet patch you could cover with a couple of bath towels is a DIY candidate; a wet room isn't. ### 5. Has it spread where you can't see? This is what turns "small" into "big". Look and feel for: - Flooring that's **soft, cupped or lifting** at the edges. - **Swelling** at the bottom of cabinets or baseboards. - **Stains on the ceiling below** if the leak was upstairs. - A **musty smell** that appears a day or two later. - Readings from a **moisture meter** at the bottom of the nearest walls and in the floor. An inexpensive pin meter from a hardware store is worth having in any house. More signs in how to find hidden water damage. ## The decision | DIY is reasonable if… | Call a professional if… | | Clean water | Gray or black water | | Caught within hours | Wet more than 48 hours, or unknown | | Hard surfaces you can see and reach | Under flooring, inside walls, in insulation or the ceiling below | | Small patch | A room or more | | Dry within a day or two, confirmed with a meter | Still damp after 48 hours, or a musty smell | | No one in the house with asthma or a weakened immune system | Vulnerable people at home | ## How to dry it properly yourself - **Remove standing water** with towels or a wet/dry vacuum (never a household vacuum). - **Empty and open up** the space: take everything out of the cabinet, remove the toe-kick if you can, pull back a loose baseboard. - **Take out what can't be saved:** soaked cardboard, swollen particleboard shelves, sodden pad. - **Move air and remove moisture:** a fan pointed into the space and a dehumidifier in the room, doors closed. Open windows only if the air outside is dry. - **Check it twice a day** by touch and with a moisture meter, comparing with a dry spot elsewhere. - **Close up only when it's really dry,** not when it looks dry. If it isn't dry within about 48 hours, stop and get a professional assessment. That's how long drying should take with professional equipment; see typical drying times. ## If it's bigger than it looked Make it safe, photograph everything and call for help the same day; read insurance or restoration company first? Local restoration help is listed in each state section: Alabama, Arkansas, Georgia, Illinois, Indiana, Iowa, Kansas, Kentucky, Maryland, Michigan, Minnesota, Mississippi, Missouri, Nebraska, New York, North Carolina, Ohio, Oklahoma, Pennsylvania, South Carolina, Tennessee, Texas, Virginia, West Virginia, Wisconsin. ## Frequently asked questions **Can I dry water damage myself?** Often, yes, if it's clean water, caught quickly, in a small area you can reach, on materials that dry well. Remove standing water, take out anything soaked that can be moved, open up the space, and run fans and a dehumidifier. If materials aren't dry within about 48 hours, call a professional. **How do I know if water got under the floor?** Signs include flooring that feels soft, cupped or lifting at the edges, a musty smell days later, and staining at baseboards. A pin-type moisture meter pressed into the floor or the bottom of the drywall near the leak gives a clearer answer. **Is particleboard under the sink ruined if it got wet?** If it has swollen or crumbles, it usually doesn't recover and should be replaced once the leak is fixed. Plywood often dries well. Either way, dry the cabinet fully before closing it up, and check behind it for wet drywall. **Should I file an insurance claim for a small leak?** Often not. If it's small, clean and dried quickly, the cost may be below your deductible, and claims can affect future premiums. If you see signs it's bigger than it looks, get a professional assessment first. **Do fans make mold worse?** Fans help drying, but don't blow air across visible mold, which spreads spores. If you can already see mold, clean small areas carefully or call a professional for larger ones. ## Sources - U.S. EPA: A Brief Guide to Mold, Moisture and Your Home - U.S. EPA: Mold cleanup in your home - CDC: Mold - IICRC: ANSI/IICRC S500 Standard for Professional Water Damage Restoration --- Guide · Inside the industry # After a storm or flood: storm chasers, 'we'll cover your deductible' and when a public adjuster is worth the fee Within a day of a major storm, the trucks arrive: crews from three states away, salespeople with clipboards, and people offering to handle your insurance for a percentage. Some of them will genuinely help. Others will be gone before your warranty matters. Here's how to tell, and what each offer really means. The short answer - **After big storms, out-of-town crews fill the gap** that local companies can't. Some are reputable; the risk is a company that won't be reachable when a warranty or dispute comes up. - **An offer to 'cover' or waive your deductible** means someone else absorbs your share of the loss, usually by inflating the claim or cutting the work. Texas prohibits it by law, and in any state it can amount to insurance fraud. - **Under the FTC's Cooling-Off Rule, most sales of $25 or more made at your home** can be cancelled within three business days. Some states add protections for storm repairs. - **FEMA doesn't send contractors to homeowners,** and its staff never charge for help or inspections. Anyone claiming to be 'FEMA approved' is a warning sign. - **A public adjuster works for you** for a percentage of the claim. It can pay off on large, complex or stalled claims. On small, simple ones, the fee often costs more than it adds. ## What happens after a big storm A hailstorm, derecho, ice storm or flood can damage thousands of homes in a day. Local restoration and roofing companies are booked for weeks. Into that gap come **traveling crews**, companies that follow storms from region to region, along with salespeople, adjusters and people who simply see an opportunity. "Storm chaser" is used as an insult, but traveling crews do much of the real recovery work after large disasters. The problem isn't that they're from out of town. It's that some of them won't be reachable in six months, when a roof leaks, a wall develops mold or a payment dispute needs resolving. Your job is to separate the ones who'll stand behind the work from the ones who won't. ## The pitches, and what's behind them | What you hear | What it usually means | | **"We'll cover your deductible."** | Someone absorbs your share of the loss, usually by inflating the claim or cutting the work. Illegal in some states, and potentially insurance fraud everywhere. | | **"Just sign so we can talk to your insurance."** | Often a contingency agreement, a binding contract, or an assignment of benefits. See before you sign. | | **"Your insurance will pay for everything."** | Nobody knows that before your adjuster has inspected and your policy has been read. | | **"We're approved by your insurance company" or "FEMA certified."** | Insurers have vendor networks, but you can verify that by calling your insurer. FEMA doesn't certify contractors for homeowners. | | **"This price is only good today."** | Pressure to sign before you check them out or talk to your insurer | | **"We need a deposit to order materials."** | Sometimes legitimate for rebuilding, rarely for emergency drying. Large cash deposits to an unverified company are the classic loss. | | **"We noticed damage on your roof."** | Ask to see photos with your house in them, and get a second opinion before signing. | ## Why "we'll cover your deductible" is a problem for you Your deductible is your share of the loss under the insurance contract. When a contractor offers to waive or absorb it, the money has to come from somewhere. Usually it's one of two places: - **A padded claim:** the estimate is raised by roughly the deductible amount, so the insurer pays it. That's insurance fraud, and it's your claim. - **Cheaper work:** the contractor keeps the price the insurer approved and cuts materials or labor to recover the cost. Some states have made it explicitly illegal. **Texas**, for example, prohibits contractors paid from a property insurance claim from waiving, absorbing or rebating the insured's deductible. Other states treat it under general fraud laws. Either way, an offer to make your deductible disappear is a reason to walk away, not a perk. ## Your right to cancel a door-to-door contract The FTC's **Cooling-Off Rule** gives you three business days to cancel most sales of $25 or more made at your home, and the seller must give you a cancellation form and explain the right. Two details matter after a disaster: - **Genuine emergencies are an exception** if you waive the right in a handwritten, signed statement describing the emergency. Read anything a salesperson asks you to write out yourself. - **Many states add their own rules** for home repair and storm work, including longer cancellation periods or cancellation if your insurer denies the claim. If a contract was signed at your door in the confusion after a storm and you're unsure about it, act on the cancellation right in writing before the deadline. ## Checking a company that isn't from here - **A local license or registration,** if your state, county or city requires one. Many require it for roofing and rebuilding. - **An insurance certificate** sent to you directly by the company's insurance agent, not a photo. - **A local address and phone number** that will still answer after the trucks leave. Ask who handles warranty calls in a year. - **Permits pulled in the company's name** where your city requires them. - **References from jobs in your area,** not only from the last storm three states away. - **No full payment until the work is done** and you've inspected it. ## FEMA, flood insurance and disaster fraud - **FEMA doesn't send contractors** to repair private homes, and it doesn't certify them. - **FEMA staff and inspectors never charge** homeowners for applying or for an inspection, and carry official identification. - **Standard homeowners policies exclude flood.** Flood damage is covered only by a separate flood policy, such as one through the National Flood Insurance Program. If you have one, it's a separate claim with its own adjuster and deadlines. - **Report suspected disaster fraud** to FEMA and to your state attorney general or insurance department. ## Public adjusters: working for you, for a fee Every adjuster the insurer sends works for the insurer. A **public adjuster** works for you. Most states license them, and they're paid a percentage of what the insurer pays on your claim, commonly around 10% to 20%. Many states cap that percentage, especially after a declared disaster. | Often worth it | Often not worth it | | Large losses: a major fire, a whole floor, an extensive contents claim | Small, straightforward claims, like a single room of clean-water damage | | A claim that has stalled or been underpaid, with clear evidence | A claim where the insurer has already offered a fair amount | | You don't have the time to manage inventories and estimates | Disputes about coverage, which may need a lawyer instead | ## How to hire a public adjuster carefully - **Check the license** with your state insurance department. Hire only someone licensed in your state. - **Negotiate what the fee applies to.** If the insurer had already offered an amount before you hired them, ask for the fee to apply only to money recovered above that offer. - **Read the contract's cancellation terms.** Many states give you a period to cancel a public adjuster contract. - **Be wary of door-knocking within hours of a disaster.** Some states restrict when public adjusters may solicit after a catastrophe. - **Ask who handles the work:** the licensed adjuster you met, or someone else in their firm. ## When to call a lawyer instead If the insurer says something isn't covered at all, or accuses you of misrepresentation, the question is legal, not one of measurement. A lawyer who handles insurance disputes for policyholders, often on contingency, is usually the right call. Your state bar association can refer you. ## The week after a storm: a short checklist - **Make the house safe** and stop more water from getting in: tarp, board up, shut off water. - **Photograph everything** before anyone starts work. - **Call your insurer** and open the claim. Write down the claim number and your adjuster's name. - **Don't sign at the door.** Take the paperwork, check the company, read it, then decide. - **Keep receipts** for emergency repairs and temporary housing. - **Start drying** wet areas within a day or two to limit mold. See what to do now. ## State rules and regulators Contractor, cancellation and public adjuster rules vary by state. Each state section covers its own: Alabama, Arkansas, Georgia, Illinois, Indiana, Iowa, Kansas, Kentucky, Maryland, Michigan, Minnesota, Mississippi, Missouri, Nebraska, New York, North Carolina, Ohio, Oklahoma, Pennsylvania, South Carolina, Tennessee, Texas, Virginia, West Virginia, Wisconsin. ## Frequently asked questions **Is it legal for a contractor to pay my insurance deductible?** In some states it's specifically illegal: Texas, for example, prohibits contractors paid from an insurance claim from waiving, absorbing or rebating the deductible. Everywhere, inflating an estimate to cover a deductible can amount to insurance fraud, which puts the homeowner at risk too. Your deductible is your share of the loss. **Can I cancel a contract I signed with a door-to-door contractor?** Usually. The FTC's Cooling-Off Rule gives you three business days to cancel most sales of $25 or more made at your home, and the seller must tell you about that right. There's an exception for genuine emergencies when you waive the right in your own handwriting. Many states add their own cancellation rights for home repair and storm work. **How much do public adjusters charge?** Most charge a percentage of the insurance payment, commonly somewhere around 10% to 20%. Many states cap public adjuster fees, especially after declared disasters. Negotiate whether the fee applies to the whole claim or only to money above what your insurer had already offered. **Is a public adjuster worth it?** Often for large, complicated or stalled claims, like a major fire, a large contents loss or a claim the insurer is underpaying. Often not for small, straightforward claims, or when the insurer has already offered a fair amount, since the fee comes out of your payment. **Does FEMA recommend contractors?** No. FEMA doesn't hire or endorse contractors for private home repairs, and FEMA staff and inspectors never charge homeowners for applying or for inspections. Be cautious of anyone claiming to be FEMA approved or certified. ## Sources - FTC: Buyer's remorse: the FTC's Cooling-Off Rule - FTC: How to avoid a home improvement scam - FEMA: Disaster fraud - NAIC: Find your state insurance department - FloodSmart (National Flood Insurance Program) - Texas Department of Insurance: How to avoid contracting scams --- Guide · Basics # Clean, gray or black water: the three categories of water damage The main factor in what a water damage job involves is how dirty the water is. Restoration companies use the IICRC S500 standard to sort it into three categories. The short answer - **Category 1** is clean water from a sanitary source, such as a burst supply line. **Category 2** (gray water) is contaminated enough to cause illness, such as washing machine discharge. **Category 3** (black water) is grossly contaminated: sewage, or floodwater from rivers and streams. - The category sets what can be saved. Clean-water jobs are mostly drying; black-water jobs remove porous materials like carpet, pad and drywall that the water touched. - Category isn't fixed. Clean water that sits for a day or two picks up contaminants and can become Category 2 or 3, which is why extraction should start the same day. - The **class** (1 to 4) describes how much material is wet and how hard it is to dry, and drives how much equipment goes in and for how long. Category 1 ### Clean water From a sanitary source: a broken supply line, an overflowing sink with no contaminants, a water heater, melting ice or snow. Category 2 ### Gray water Significant contamination that could cause illness: washing machine or dishwasher discharge, a toilet overflow with urine but no feces, an aquarium, a failed sump. Category 3 ### Black water Grossly contaminated: sewage, toilet overflow with feces, rising floodwater from rivers or streams, and water that has sat long enough to grow microbes. ## Why the category matters Category 1 jobs are mostly about drying. Carpet, padding and drywall can often be saved if extraction and drying start quickly. Category 2 adds cleaning and antimicrobial treatment. Carpet padding is usually replaced, and porous materials that soaked it up may need to come out. Category 3 is a contamination job. Technicians wear protective equipment, porous materials that the water touched (carpet, pad, drywall, insulation, upholstered furniture) are generally removed and discarded, and everything left is cleaned and sanitized. Children, older adults, pregnant people and anyone with a weakened immune system should stay out until it's done. ## Water gets dirtier as it sits Category is not fixed. Clean water picks up contaminants from flooring, wall cavities and dust, and microbes multiply in warm, still water. A clean supply-line leak left for a few days can become Category 2 or 3 water. That's the practical reason to start extraction the same day. ## Classes: how much is wet The S500 standard also sorts jobs into classes based on how much material got wet and how hard it will be to dry. The class drives how much drying equipment goes in and how long it runs. | Class | What's wet | Typical example | | Class 1 | A small area; little water absorbed into porous materials | A dishwasher leak caught quickly on a tile floor | | Class 2 | A significant share of the room, such as carpet and the lower part of walls | A washing machine hose that ran for an hour | | Class 3 | Most of the room's surfaces, often because water came from above | A burst pipe in an upstairs bathroom soaking the ceiling below | | Class 4 | Water held deep in dense materials such as hardwood, plaster, brick or concrete | A flooded basement with a finished hardwood floor | ## Questions to ask the restoration company - What category and class did you assign, and why? - Which materials can be dried in place, and which need to be removed? - Will you take and record moisture readings every day until the job is dry? - Are your technicians IICRC certified in water damage restoration? ## Frequently asked questions **Is water from a toilet Category 2 or Category 3?** A toilet overflow with urine but no feces is generally treated as Category 2. An overflow containing feces, or any sewage backing up from a drain, is Category 3. **Is rainwater coming through the roof clean water?** Rain is usually Category 1 when it first comes in, but it picks up dirt from roofing, insulation and attic dust on the way. Wet insulation and ceiling drywall from a roof leak often have to come out regardless of category. **Can I clean up Category 3 water myself?** It isn't recommended. Sewage and floodwater can carry bacteria, viruses and parasites. Porous materials it touched generally have to be removed and discarded, and the space sanitized, by people wearing protective equipment. Children, older adults, pregnant people and anyone with a weakened immune system should stay out until it's done. **What is the difference between a water damage category and class?** Category describes contamination: how dirty the water is. Class describes the extent: how much of the room is wet and how much water the materials absorbed. A small, clean leak is Category 1, Class 1. A sewage backup across a finished basement could be Category 3, Class 2 or 3. ## Sources - IICRC: ANSI/IICRC S500 Standard for Professional Water Damage Restoration - U.S. EPA: Mold cleanup in your home - CDC: Clean up safely after a disaster --- Guide · Inside the industry # What your adjuster is listening for: the facts and phrases that decide a water damage claim Two kitchens with identical water damage can end with one claim paid in full and the other denied. The difference is usually not the damage. It's how the cause and the timing were described, and what evidence backs that up. Here's what adjusters are trained to find, so you can describe your loss accurately and completely. The short answer - **Water claims are decided by cause and timing.** Standard homeowners policies cover sudden and accidental discharge, and exclude flood, wear and tear, and constant or repeated seepage over weeks, months or years. - **The seepage exclusion has an exception many people never hear about:** common policy forms restore coverage when the leak was hidden inside walls, ceilings or under floors and unknown to you. Read your own policy's wording. - **Wear and tear usually excludes the failed part, not the water damage it caused.** An old pipe that bursts typically isn't replaced by the policy, but the resulting damage often is covered. - **Describe what you saw and when, not what you guess.** 'I don't know how long it was leaking' is accurate. 'It's probably been going a while' is a guess that points straight at an exclusion. - **Evidence speaks louder than words:** the plumber's written cause, dated photos, and the failed part itself. Keep the broken hose or valve; your insurer may want it. ## The two questions behind every water claim An adjuster's first job on a water claim isn't to measure the damage. It's to answer two questions: - **Where did the water come from?** A burst supply line, an appliance, a roof opening in a storm, rising surface water, a backed-up drain, groundwater through the foundation. - **How long did it go on?** A sudden event, or something that leaked, seeped or condensed over weeks or months. Those answers decide which part of the policy applies. The damage estimate comes after. That's why the first conversation with your insurer, often a phone call you make while standing in wet socks, matters more than most people realize. ## How the policy sorts water | Cause | Typical treatment in a standard homeowners policy | | **Sudden and accidental discharge** from plumbing, heating, air conditioning or an appliance | Usually covered | | **Constant or repeated seepage or leakage** over weeks, months or years | Usually excluded, with an exception in many policies for hidden, unknown leaks | | **Wear and tear, rust, deterioration** | The worn part is excluded; the resulting water damage often isn't | | **Flood** (surface water, rising water) | Excluded; needs separate flood insurance | | **Sewer or drain backup** | Excluded unless you added a backup endorsement | | **Groundwater** through foundations | Usually excluded | | **Mold** | Often excluded or capped by a sublimit, except as part of a covered water loss | | **Freezing** | Usually covered if you kept the heat on or shut off and drained the water while away | Your policy's wording is what actually counts, and forms differ. More detail is in what insurance covers. ## The exception hidden in the seepage exclusion The seepage exclusion is the most common reason water claims are denied, and its exception is the least understood. Widely used homeowners policy forms exclude constant or repeated seepage over a period of weeks, months or years, and older versions used a fixed period such as 14 days. But many of those same forms restore coverage when the seepage was **hidden within walls or ceilings or beneath floors** and **unknown to everyone insured** under the policy. In plain terms: a slow drip inside a wall that you couldn't have seen may be treated very differently from a slow drip under a sink you looked at every day. If your claim is questioned on seepage grounds, ask the adjuster for the exact policy language being applied, and read whether that exception appears in it. ## Phrases that point toward an exclusion None of this is about hiding anything. Misrepresenting a claim can void a policy, and it's fraud. It's about the difference between **what you know** and **what you're guessing**. People under stress tend to guess out loud, and guesses often point at exclusions that the facts don't support. | What people often say | What it can signal | The accurate alternative, if true | | "It's probably been leaking for a while." | Long-term seepage | "I found it on Tuesday morning when I saw water on the floor. I don't know when it started." | | "I've noticed a smell for months." | Known, ongoing problem | Say only what you noticed and when. If the smell started recently, say so. | | "The pipes are old." | Wear and tear | "The supply line under the sink split." Let the plumber state the cause in writing. | | "Water came in from outside." | Flood or groundwater | Describe exactly where you saw water enter: through the ceiling, around a window, up through the floor drain. | | "There's mold everywhere." | Mold exclusion or sublimit | Describe the water damage first, then the growth you've actually seen, and where. | | "I meant to fix that." | Neglect | If you knew of a problem, say so honestly, and say what happened differently this time. | **The rule of thumb:** state what you saw, where, and when. When you don't know something, say "I don't know." Don't speculate about causes or durations; let the plumber's report and the evidence do that. ## Who your adjuster is, and how they work | Type | Works for | What to know | | **Staff field adjuster** | Your insurer | Visits in person. Usually handles larger or more complex claims. | | **Desk adjuster** | Your insurer | Works from photos, video calls and contractor estimates, often on a heavy caseload. What isn't photographed often doesn't get paid. | | **Independent adjuster** | An adjusting firm hired by your insurer | Inspects and writes the estimate; the insurer makes the payment decision. Common after storms. | | **Catastrophe adjuster** | Your insurer or an adjusting firm | Brought in from other regions after large events. May be unfamiliar with local prices. | | **Public adjuster** | You | Licensed in most states, paid a percentage of your claim. See when a public adjuster helps. | Every adjuster on the insurer's side works within an **authority limit**: the amount they can approve without a supervisor. If your claim stalls just above a round number, it may be waiting on a higher level of approval. It's fair to ask, "Is this within your authority, or does someone else need to approve it?" ## The recorded statement Most policies require you to cooperate with the investigation. That can include a recorded statement and, in disputed claims, an examination under oath. Cooperating doesn't mean improvising. - **Schedule it.** You can usually ask for a time when you have your policy, photos and notes in front of you. - **Write a short timeline first:** when you found the water, what you did, who you called, and when. - **Answer the question asked.** Short, factual answers are fine. - **Say "I don't know" or "I'm not sure"** whenever that's the truth. It's a complete answer. - **Ask for a copy** of the recording or transcript, and correct any mistakes in writing afterward. ## Evidence that matters more than any phrase - **The plumber's invoice with a stated cause,** such as "burst supply line" or "pipe split due to freezing." Ask the plumber to write it on the invoice. - **Dated photos and video** of the water, the source and every affected room, taken before anything is moved. - **The failed part.** Keep the split hose, cracked fitting or failed valve in a labeled bag. Your insurer may want to inspect it, and if a defective product caused the leak, the insurer may pursue the manufacturer. Throwing it away can complicate both. - **Moisture logs** from the restoration company, showing the extent of the water. See is it actually dry. - **Receipts** for emergency expenses: towels, fans, a hotel night, the plumber. ## Your duty to limit the damage Policies require you to take reasonable steps to protect the property from further damage: stop the water, start drying, cover openings. Damage that happens because nobody acted can be reduced or denied. That's why waiting for the adjuster before calling anyone to dry the house is usually a mistake. See who to call first. ## Letters you may receive - **Reservation of rights:** the insurer is investigating and may later decide some or all of the claim isn't covered. It isn't a denial. Ask which provisions it's reserving rights under. - **Request for proof of loss:** a sworn statement of what you're claiming, often with a deadline. Don't miss it; ask for an extension in writing if you need one. - **Partial denial:** some items paid, some not. Ask for the reason for each denied item, with the policy language, in writing. ## How you're paid: ACV and depreciation Many policies first pay **actual cash value**: the replacement cost minus depreciation. The withheld depreciation is often **recoverable** once repairs are done or items are replaced, usually within a deadline set by the policy. Keep every receipt, and diary the deadline. ## If the claim goes wrong - Ask for every decision and its reason in writing. - Escalate to the adjuster's supervisor. - Contact your state insurance department's consumer line about claim handling. - Check your policy's appraisal clause for disputes over the amount of loss. - For large or denied claims, consider a licensed public adjuster or an attorney. ## Your state's insurance regulator Each state section lists its insurance regulator and claim rules: Alabama, Arkansas, Georgia, Illinois, Indiana, Iowa, Kansas, Kentucky, Maryland, Michigan, Minnesota, Mississippi, Missouri, Nebraska, New York, North Carolina, Ohio, Oklahoma, Pennsylvania, South Carolina, Tennessee, Texas, Virginia, West Virginia, Wisconsin. ## Frequently asked questions **What does the adjuster look for on a water damage claim?** Mainly the cause of the water and how long it went on. Sudden and accidental leaks are usually covered; flooding, long-term seepage, wear and tear, and neglect usually aren't. The adjuster also checks whether you took reasonable steps to limit the damage. **Do I have to give a recorded statement?** Most policies require you to cooperate with the investigation, which can include a recorded statement or, in some cases, an examination under oath. You can usually schedule it for a time that works, have your policy and notes in front of you, and ask for a copy afterward. Answer what you know and say when you don't know. **Is a leak that went on for weeks ever covered?** Sometimes. Many policies exclude constant or repeated seepage over weeks or longer, but common policy forms make an exception when the leak was hidden within walls, ceilings or floors and unknown to you. Wording varies, so read your policy and ask the adjuster which language applies. **My pipe failed because it was old. Is that covered?** The pipe itself usually isn't, because wear and tear is excluded. The water damage the failure caused often is covered as a sudden and accidental discharge. Ask the adjuster to separate the two in writing. **What is a reservation of rights letter?** A letter saying the insurer is investigating your claim but may later decide some or all of it isn't covered. It's not a denial. Keep cooperating, keep documenting, and ask the insurer which policy provisions it's reserving rights under. **Should I keep the broken part?** Yes. Keep the failed supply line, valve, fitting or appliance part, labeled with the date. Your insurer may want to inspect it, and if a product defect caused the leak, the insurer may pursue the manufacturer. Throwing it away can complicate the claim. ## Sources - NAIC: Consumer guide to homeowners insurance - Insurance Information Institute: Understanding the insurance claims payment process - NAIC: Find your state insurance department --- Guide · Emergency # Water damage or mold emergency: what to do before help arrives The hour between finding the water or the mold and the restoration crew pulling up decides how much has to be torn out, and how clean your insurance claim is. Here's what to do with it. The short answer - **1. Make it safe.** Stay out of water that could reach outlets, cords or the electrical panel. Turn off power to the wet area only if you can reach the breaker panel without standing in water; otherwise call your electric utility. Leave if you smell gas or a ceiling is sagging. - **2. Stop the water.** Close the fixture's own valve, or the main shutoff where the water line enters the house, turning it clockwise. - **3. Photograph everything before cleanup.** Take a walk-through video and photos of the source, waterlines and damaged belongings, and keep the failed part for your insurer. - **4. Don't reach for bleach.** The EPA doesn't recommend bleach as a routine part of mold cleanup: dead mold can still cause allergic reactions and has to be removed, and bleach can't fix mold inside drywall or wood. Don't disturb large patches or run the HVAC if it may be contaminated. - **5. Call for help with the facts ready:** what caused the water, whether it's clean or sewage, how many rooms or square feet are wet, how long it's been wet, and your insurer and claim number. The EPA advises drying wet materials within 24 to 48 hours to prevent mold. ## Step 1: make it safe Electricity, gas and falling ceilings are the real emergencies. The water damage can wait five minutes. - **Water near outlets, cords, a space heater or the electrical panel:** don't step in it. Shut off the breaker for that area only if you can reach the panel standing on dry ground. Otherwise call your electric utility to cut power at the meter. - **A gas smell:** leave without switching anything on or off, and call your gas utility or 911 from outside. - **A sagging or bulging ceiling:** keep everyone out of the room. Wet drywall can drop without warning. - **Sewage or floodwater:** keep children and pets away, and wear rubber boots and gloves if you have to go in. ## Step 2: stop the water - **For an appliance or toilet,** close the small supply valve behind it. - **For a burst pipe or a leak you can't isolate,** close the main shutoff. It's usually where the water line comes through the foundation wall or slab, often near the meter or water heater. Turn it clockwise. On a well, switch off the well pump breaker. - **Open a low faucet** to drain the pipes, and turn off the water heater so it doesn't run empty. - **For a roof leak or storm water,** catch the drips, and don't go on the roof in the rain. See roof leaking into the house. ## Step 3: document before you move anything Insurers decide claims on evidence. A minute of video now saves arguments later. - Walk every affected room on video, then photograph the source, waterlines on walls, and the bottoms of furniture and cabinets. - Photograph visible mold with something for scale, such as a tape measure. - Keep the failed part: the split supply line, the cracked fitting, the burst hose. - Write down when you found it, and every call you make. ## Found mold? What not to do Mold found behind a baseboard or under a sink is rarely an emergency on its own, but the wrong first move can spread it. - **Don't spray bleach on it.** The EPA says killing mold with a biocide like chlorine bleach isn't recommended as a routine practice, because dead mold can still cause allergic reactions and has to be removed anyway. On drywall, wood and carpet, bleach can't reach growth inside the material. Never mix bleach with ammonia or other cleaners. - **Don't scrape, sand or dry-brush large patches.** That puts spores into the air. Leave anything bigger than about 10 square feet (3 feet by 3 feet) for a professional. - **Don't run the heating or cooling** if you know or suspect mold is in the ducts or air handler. It can spread spores through the house. - **Don't paint or caulk over it.** It keeps growing underneath. - **Do find the water.** Mold always has a moisture source: a slow leak, condensation, a damp crawl space or high humidity. Cleaning without fixing it means it comes back. How to find hidden water damage. ## While you wait for the restoration company - Move electronics, documents, photos and rugs to a dry floor. - Put foil or wood blocks under furniture legs so stain doesn't wick into carpet. - Mop and blot clean water. Don't use a household vacuum on water, and don't touch sewage. - Open windows if the weather is dry, and run fans only where nothing electrical sits in water. - Call your insurer to open a claim, and ask whether they need to approve the mitigation company before work starts. Professional water damage restoration under the IICRC S500 standard uses moisture meters, thermal cameras, air movers and dehumidifiers to dry the inside of walls and floors, not just what you can see. Mold remediation under IICRC S520 seals the work area with plastic sheeting and negative air pressure so spores don't spread. ## What to tell the company when you call A restoration company will triage your call with the same few questions. Having the answers ready gets the right crew and equipment sent the first time. - **What caused it:** supply line, appliance, water heater, roof, storm, groundwater, sewer backup, or a fire put out with water. - **What kind of water:** clean (from a supply line), gray (washer, dishwasher, toilet overflow without feces) or black (sewage, floodwater). See the three water categories. - **How big:** which rooms and floors, roughly how many square feet, and whether it reached ceilings below or the basement. - **How long:** when it started, or your estimate. Water that has sat more than 48 hours usually means mold and more tear-out. - **Insurance:** your insurer, whether you've opened a claim, and the claim number if you have one. - **Who's in the house:** anyone with asthma, a weakened immune system, a baby or an elderly person, which changes how the work is set up. Ask for an arrival estimate, what they'll do on the first visit, and whether they bill your insurer directly. Read anything you sign, especially an assignment of benefits. ## After a fire Fire damage is almost always water damage too, from the hoses or sprinklers that put it out. Don't go back in until the fire department says the building is safe, and don't turn utilities back on yourself. Don't wipe soot off walls or upholstery, which smears it deeper, and photograph everything before anything is thrown out. The same drying clock applies: wet materials need to start drying within 24 to 48 hours. ## Steps for your state Each state section has a first-hour guide with that state's insurance regulator and claim rules, plus county pages with local housing and weather data: Alabama, Arkansas, Georgia, Illinois, Indiana, Iowa, Kansas, Kentucky, Maryland, Michigan, Minnesota, Mississippi, Missouri, Nebraska, New York, North Carolina, Ohio, Oklahoma, Pennsylvania, South Carolina, Tennessee, Texas, Virginia, West Virginia, Wisconsin. ## Frequently asked questions **What should I do first when my house floods or a pipe bursts?** Make it safe first: stay out of water near outlets or the electrical panel and leave if you smell gas. Then shut off the water at the fixture valve or the main shutoff, photograph the damage before cleanup, and call a restoration company and your insurer. Drying should start within 24 to 48 hours. **Should I use bleach on mold after water damage?** Usually not. The EPA says biocides such as chlorine bleach aren't recommended as a routine practice in mold cleanup, because dead mold can still cause allergic reactions and must be removed anyway. Scrub hard surfaces with detergent and water, and remove moldy drywall, carpet and insulation. If you do use bleach, never mix it with ammonia or other cleaners. **Should I turn off the electricity if there's water in the house?** Only if you can reach the breaker panel while standing on dry ground. If water is near outlets, cords or the panel, stay out of the room and call your electric utility to disconnect power at the meter. **What will a restoration company ask when I call?** Expect questions about the source (pipe, appliance, roof, storm, sewer), whether the water is clean or contaminated, how many rooms or roughly how many square feet are wet, how long it has been wet, whether ceilings are sagging, and whether you've opened an insurance claim. Having those answers ready speeds up dispatch. **Can I clean up mold myself?** The EPA's rule of thumb is that a homeowner can usually handle an area under about 10 square feet if the water was clean and no one in the house has asthma or a weakened immune system. Larger areas, mold in walls or ductwork, and mold after sewage or floodwater call for a professional remediation company. **Do I have to wait for the insurance adjuster before starting cleanup?** No. Most policies expect you to take reasonable steps to prevent further damage. Document the damage first, tell your insurer you're starting mitigation, and keep receipts. Don't tear out materials before photographing them. ## Sources - U.S. EPA: A Brief Guide to Mold, Moisture and Your Home - U.S. EPA: Should I use bleach to clean up mold? - U.S. EPA: Mold cleanup in your home - CDC: Mold - IICRC: ANSI/IICRC S500 Standard for Professional Water Damage Restoration - IICRC: ANSI/IICRC S520 Standard for Professional Mold Remediation --- Guide · Cost # How much does water damage restoration cost? Most water damage jobs land in the low thousands, but the range is wide. Here's what the national cost guides show and the factors that move your bill. The short answer - Published 2026 national cost guides put a typical water damage job at about **$1,300 to $6,400**, averaging near $3,900, including mitigation and common repairs. - Drying and extraction alone usually run about $3 to $4 per square foot for clean water, $4 to $6.50 for gray water, and $7 and up for black water such as sewage. - Mold remediation commonly runs about $500 to $12,000 (average near $3,000), and fire and smoke restoration about $2,900 to $38,000. - The main cost drivers are the water category, how long the water sat, the materials involved and how much has to be opened up to reach it. Starting drying the same day does more than anything else to keep the bill down. - If the cause is covered, you usually pay your deductible and the insurer pays the rest of the approved scope. These are national ranges from published 2026 cost guides, not quotes. Prices vary by region and town, by contractor, and above all by how much is wet and how dirty the water is. Get a written estimate. ## Typical ranges | Job | Common range | Notes | | Water mitigation, Category 1 (clean) | About $3 to $4 per sq ft | Extraction and drying. Least expensive if started within a day. | | Water mitigation, Category 2 (gray) | About $4 to $6.50 per sq ft | Adds antimicrobial treatment. Pad and some drywall usually replaced. | | Water mitigation, Category 3 (black) | About $7 per sq ft and up | Protective equipment, removal of porous materials, sanitizing. | | Whole water damage job | About $1,300 to $6,400, averaging near $3,900 | Mitigation plus typical repairs. | | Mold remediation | About $500 to $12,000, averaging near $3,000 | Small bathroom jobs at the low end; whole-house jobs far higher. | | Fire and smoke restoration | About $2,900 to $38,000, averaging near $20,000 | Driven by how far smoke and soot traveled, and water from firefighting. | ## What pushes the price up - **Category of water.** Contaminated water means more removal and more cleaning. - **Time.** Every day of waiting lets water wick higher and adds the risk of mold. - **Materials.** Hardwood, plaster and finished basements take longer to dry and cost more to replace. - **Access.** Water inside walls, under cabinets or in crawl spaces needs more demolition to reach. - **After-hours work.** Nights, weekends and holidays can cost more. - **Rebuild.** Mitigation (drying) and reconstruction (new drywall, paint, flooring) are often billed separately. ## What pushes it down - Shutting off the water quickly and starting drying the same day. - Moving belongings out of wet rooms yourself. - Choosing a company that dries in place with moisture monitoring, instead of removing materials by default. ## A worked example Say a supply line under an upstairs bathroom sink fails while you're at work, and water runs for six hours across 300 square feet of bathroom, hallway and the kitchen ceiling below. That's clean water (Category 1), but it came from above and soaked ceilings, walls and floors (likely Class 3). - **Mitigation:** extraction, removing the wet ceiling drywall and insulation below, and three to five days of drying at roughly $3 to $4 per square foot, or about $900 to $1,200 for the wet area, plus equipment and demolition line items. - **Reconstruction:** new ceiling drywall, paint and any flooring that couldn't be dried. This is often billed separately and can equal or exceed the mitigation cost. If the same leak had been caught in 30 minutes, it might have been a Class 1 job dried with a few air movers and no demolition at all. ## How insurance changes the math If the cause is covered, you usually pay your deductible and the insurer pays the rest of the approved scope. Many restoration companies bill the insurer directly using estimating software the insurer also uses. Ask before work starts what's covered, what your deductible is, and whether anything will be billed to you separately. If the cause isn't covered, ask for an itemized estimate and compare at least two. ## Frequently asked questions **How much does it cost to dry out a flooded basement?** For clean water, drying and extraction alone often run about $3 to $4 per square foot, so a 600-square-foot basement might be roughly $1,800 to $2,400 before any rebuild. Sewage or floodwater costs more because porous materials have to be removed and the space sanitized. Finished basements cost more than unfinished ones. **Why are restoration estimates so different from each other?** Companies may assign different water categories and classes, plan to remove different amounts of material, or bundle reconstruction with drying. Ask each one for an itemized scope with the category, class, square footage, equipment count and number of drying days, so you're comparing the same job. **Do restoration companies charge for an inspection?** It varies. Some roll the inspection into the job, and some charge a service or trip fee, especially after hours. Ask before they come out. **Is water damage restoration paid by insurance?** If the cause is covered, such as a sudden pipe burst, insurance usually pays the approved cost after your deductible. Gradual leaks, flooding from outside and sewer backups without an endorsement usually aren't covered. ## Sources - LawnStarter: How much does water damage restoration cost in 2026? - LawnStarter: Fire and smoke damage restoration cost in 2026 - HomeAdvisor: Fire and smoke damage repair cost --- Guide · Appliances # Water heater leaking: what to do and when it needs replacing Water heaters fail in two ways: a slow drip that rots the floor, or a tank that splits and dumps 40 to 80 gallons. Either way, the first steps are the same. The short answer - First turn off the energy (gas control to off or pilot, or the electric breaker), then close the cold-water supply valve on top of the tank. - A leak from the pipe fittings on top or the drain valve is usually repairable. Water coming from the bottom of the tank itself usually means the tank has corroded through and must be replaced. - Water from the temperature and pressure relief valve means it may be doing its job. Never cap or plug that valve; have a plumber find out why it's opening. - Water damage from a sudden tank failure is usually covered by homeowners insurance. The water heater itself, and damage from a slow leak, usually aren't. ## Shut it down - **Turn off the energy.** Gas: turn the control knob to off or pilot, and close the gas valve on the supply line. Electric: switch off the water heater's breaker. - **Close the cold water supply valve** on the pipe going into the top of the tank. If it won't turn, shut off the main. - **Let the water cool** for a few hours if you need to drain it. Tank water can be hot enough to scald. - **Drain the tank if it's leaking from the bottom.** Attach a garden hose to the drain valve near the bottom, run it to a floor drain or outside, open a hot faucet upstairs to let air in, and open the drain valve. ## Where is it leaking from? | Location | Likely cause | Usually means | | Pipe connections on top | Loose fitting or corroded connector | Repairable | | Temperature and pressure relief valve or its discharge pipe | Valve doing its job because pressure or temperature is too high, or a failing valve | Needs a plumber to diagnose. Never cap or plug this valve. | | Drain valve at the bottom | Valve not fully closed or worn out | Repairable | | Bottom of the tank or under the jacket | Tank corroded through | Replace the water heater | | Puddle with no visible drip | Condensation on a cold tank, or a leak from a nearby pipe or furnace | Dry everything, then watch where the water reappears | ## Signs the tank is near the end - Rusty or discolored hot water, but not cold. - Rumbling or popping from sediment buildup. - Moisture or rust around the base. - Age. Tank water heaters commonly last around 8 to 12 years. The manufacture date is usually coded into the serial number on the label. ## Dry the area quickly Water heaters usually sit in basements, garages, utility closets or, in some homes, an upstairs closet over a finished ceiling. Mop up standing water, pull wet boxes and rugs away, and check the drywall and baseboards around the closet with your hand. If water ran under walls or into a finished ceiling, it needs professional drying: the EPA advises drying water-damaged materials within 24 to 48 hours to prevent mold. ## Limit the damage next time - Set the tank in a drain pan piped to a floor drain, especially in a finished basement or upstairs closet. - Add a water leak sensor or an automatic shutoff valve. - Flush sediment once a year, following the manufacturer's instructions. - Ask a plumber to check the anode rod and whether you need a thermal expansion tank. ## Insurance Water damage from a sudden tank failure is usually covered. The water heater itself, and damage from a slow leak that went on for weeks, usually aren't. See what homeowners insurance covers. ## Frequently asked questions **Is a leaking water heater an emergency?** A steady leak or a puddle that keeps growing is. Shut off the energy and the cold-water supply right away. A tank that splits can release its whole volume, 40 to 80 gallons, in minutes. A few drops from a fitting can wait for a plumber, but put a pan or towels down and check it every few hours. **Can I still use hot water if the water heater is leaking?** Not safely if the tank itself is leaking. If the leak is at a fitting and you've tightened it and it's stopped, you can restore power or gas. Otherwise leave it off until a plumber has looked at it. **How long do tank water heaters last?** Commonly around 8 to 12 years, depending on water quality and maintenance. The manufacture date is usually coded into the serial number on the tank's label. **Why is water coming out of the pipe on the side of my water heater?** That's the temperature and pressure relief valve's discharge pipe. Water there means the tank's temperature or pressure got too high, often from a thermostat problem or thermal expansion, or that the valve is failing. It's a safety device, so have a plumber diagnose it rather than plugging it. ## Sources - U.S. Department of Energy: Storage water heaters - U.S. Department of Energy: Selecting a new water heater --- Guide · Money # The water mitigation bill is higher than expected, or insurance won't pay all of it: what to do Drying a house for four days can cost thousands of dollars, and it often surprises people twice: once when the invoice arrives, and again when the insurer pays less. Most of these disputes come down to documentation. Here's how to read the bill and settle the gap. The short answer - **Ask for the full file:** the itemized invoice, daily moisture readings (drying logs), photos, and the equipment placed each day. Professional drying under the IICRC S500 standard is documented. - **Check the usual pressure points:** equipment left after readings showed dry, more machines than the area needed, tear-out not shown in photos, and charges that don't match what you saw. - **Compare it with the insurer's estimate** line by line. Many gaps are about a handful of items, not the whole bill. - **Escalate in order:** the company, the adjuster, a written dispute, your state insurance department's consumer line, then mediation, appraisal or small claims where available. - **Don't ignore the bill.** Unpaid contractors can often file a lien. Keep talking, in writing. ## First, why these bills are big Mitigation is mostly equipment and visits. A typical water job bills for: - **Emergency service and water extraction.** - **Equipment per day:** air movers, dehumidifiers, sometimes air scrubbers. Several machines for several days adds up fast. - **Daily monitoring:** a technician's visit to take moisture readings and adjust equipment. - **Removal and disposal** of materials that can't be dried: soaked carpet pad, wet drywall, baseboards. - **Antimicrobial application** and **containment** where needed, especially with gray or black water. None of that is suspicious on its own. What you want to check is whether the **quantities** match what the drying actually needed. ## Ask for the full file Before arguing about the number, ask the company in writing for: - The **itemized invoice**, with quantities and unit prices. - The **drying logs:** daily moisture readings at each monitored point, with the drying goal. - The **equipment log:** which machines were in which room on which days. - **Photos** before, during and after, especially of anything removed. - The **signed work authorization** and any change orders. Professional water damage restoration under the **IICRC S500** standard is measured and recorded. A company that did the work properly should be able to produce these quickly. ## The charges most often questioned | Line item | What to check | | **Equipment days** | Did equipment stay after the logs show materials reached the drying goal? | | **Number of machines** | Does the count make sense for the affected area? Ask how it was calculated. | | **Demolition and tear-out** | Do photos show the material was wet or contaminated? Was it actually removed? | | **Water category** | Was clean water billed as gray or black? Category drives protective equipment, antimicrobials and what has to go. See the three categories. | | **Monitoring visits** | Do the dates match the visits you remember? | | **After-hours or emergency charges** | Were they disclosed when you called? | ## When insurance pays less than the bill This is the most common version of the problem. The insurer writes its own estimate, often with the same estimating software, and it comes out lower. Usually the difference sits in a few lines. - **Get both documents side by side:** the company's invoice and the insurer's estimate. - **Mark each line** as matching, different quantity, or missing. - **Send the company's documentation to the adjuster** for the differences, especially drying logs and photos, and ask for a written explanation of anything still denied. - **Ask the company to talk to the adjuster directly.** Many disputes resolve once both sides look at the same logs. - **Check whether some items simply aren't covered**, such as a gradual leak, or mold above a policy limit. See what insurance covers. ## If you're still stuck - **Write a dispute letter** to the company listing each line you question and why. Offer to pay the undisputed amount. - **Call your state insurance department's consumer line** if the problem is how the insurer handled the claim. - **Check your policy for an appraisal clause**, used for disagreements about the amount of loss, and ask whether your state runs a mediation program. - **For large amounts,** a lawyer or a licensed public adjuster can advise on your options. - **Small claims court** is an option for modest amounts in many states. Throughout, **stay in writing and keep responding**. Unpaid contractors can often file a lien on the property; a documented, good-faith dispute puts you in a far better position than silence. ## Preventing it next time - Read the work authorization before signing, especially how the price is set. - Ask on day one for daily moisture readings to be shared with you. - Ask on day three, "What's left before we reach the drying goal?" ## Find a restoration company near you Each state section lists county pages with local help and that state's insurance regulator: Alabama, Arkansas, Georgia, Illinois, Indiana, Iowa, Kansas, Kentucky, Maryland, Michigan, Minnesota, Mississippi, Missouri, Nebraska, New York, North Carolina, Ohio, Oklahoma, Pennsylvania, South Carolina, Tennessee, Texas, Virginia, West Virginia, Wisconsin. ## Frequently asked questions **Why is water mitigation so expensive?** It's equipment and labor intensive. Air movers, dehumidifiers and sometimes air scrubbers run for several days, technicians visit daily to take moisture readings and adjust equipment, and wet materials may be removed and disposed of. Each of those is usually billed per item, per day. **My insurance paid less than the mitigation bill. Do I owe the difference?** Usually you're responsible under the contract you signed, unless you assigned your benefits to the company. But many gaps are negotiable: ask the company and the adjuster to reconcile the invoice against the insurer's estimate, line by line, using the drying logs and photos. **What are drying logs?** Daily records of moisture readings at marked points in each affected area, plus the equipment in place. They show when materials reached their drying goal, which is the main evidence for how many equipment-days were justified. **Can a restoration company put a lien on my house?** In many states contractors can file a mechanic's lien for unpaid work, subject to notice rules and deadlines. That's why it's better to dispute in writing and keep negotiating than to stop responding. **Who can help me with a mitigation billing dispute?** Start with the company and your adjuster. If you're stuck, call your state insurance department's consumer line about the insurer's handling of the claim. Some policies have an appraisal clause for disputes over the amount of loss, and some states offer mediation programs. For larger amounts, a lawyer or public adjuster can advise. ## Sources - IICRC: ANSI/IICRC S500 Standard for Professional Water Damage Restoration - NAIC: Find your state insurance department - Insurance Information Institute: Understanding the insurance claims payment process - U.S. EPA: A Brief Guide to Mold, Moisture and Your Home --- Guide · Inside the industry # Who actually answers when you call a water damage number? How restoration jobs are referred, bought and sold Search 'water damage near me' at 2 a.m. and call the first number you see. The voice that answers may belong to the company that will dry your house, a franchise call center, a network that sells your call to a local company, or a business that only exists as a map pin. Here's how that market works, including our part in it. The short answer - **Water damage jobs are valuable, so they're bought and sold.** Plumbers, property managers and agents often receive referral fees, and call networks and ad platforms sell calls to local companies. - **The number you dial may not belong to the company that shows up.** Franchise brands route calls to a local owner, call networks route to a participating company, and some jobs are passed on to subcontractors. - **None of that makes a company bad,** but it means a recommendation isn't neutral. Treat any referral, including ours, as a starting point. - **Two minutes on the phone settles most of it:** ask for the legal business name, who will physically come, whether they're IICRC certified, and what you owe if you don't hire them. - **Then check three records:** your state's business registry, any contractor license your state or city requires, and the IICRC certified firm locator. ## Why your call is worth money A single water damage job often runs into thousands of dollars, is usually paid by insurance, and frequently leads to a second job: the rebuild. Very few homeowners shop around at the moment they need help. Put those together and the phone call itself becomes valuable, so an entire market has grown up around getting you to call one number rather than another. That market isn't secret, but it's rarely explained to the person making the call. Here's how it works. ## Six ways a call reaches a restoration company | Route | Who's on the other end | How money changes hands | | **The company's own number** | The local business that will do the work | The company pays for its own ads or listing | | **A national franchise brand** | Often a central call center, which dispatches the local franchise owner for your area | The franchisee pays royalties and marketing fees to the brand | | **Your insurer's program** | A company in the insurer's or its administrator's network | The company agrees to the program's pricing and rules. See preferred vendors. | | **A personal referral** | Whoever your plumber, property manager, agent or HOA recommends | Referral fees per job are common | | **A call network or lead service** | A participating company in your area, reached through a routed number | The company or network pays per qualifying call or lead. This site works this way. | | **Ad platforms** | Advertisers on search ads and Google's Local Services Ads | Pay per click or per lead. Local Services Ads involve license and background checks by Google. | ## The plumber's recommendation The plumber who fixes your burst pipe is often the first professional to see the water damage, so their recommendation carries weight. In this industry, restoration companies commonly pay plumbers, and sometimes property managers and others, a fee for each job they refer. That's generally legal, and the plumber may genuinely like the company. Just know that the recommendation isn't neutral. It's fair to ask, "Do you get paid if I use them?" A good plumber won't mind the question. Either way, check the company yourself before signing. The plumber's other common line, "you need a restoration company," is usually honest. Water that has soaked into drywall, under flooring or into a ceiling rarely dries properly with household fans. If you're unsure, see dry it yourself or call a pro. ## Franchise brands and call centers Several national restoration brands are franchise systems. The name on the truck is national, while the business that does your job is a locally owned franchise. Calls to the national number are often answered by a central call center and dispatched to whoever owns your territory. That can work well: shared training, standard paperwork, after-hours coverage. It also means quality varies with the local owner, not the brand. Judge the franchise that serves your address, not the commercial. ## Call networks and lead services, including us Some websites and ads don't belong to any restoration company. They answer or route your call and connect you with a participating company that serves your area, and they're paid when that connection happens. Restoration calls are among the more expensive home-service leads, which is why so many of these sites exist. **Local Water & Mold is one of them.** Our phone line connects callers with participating local restoration companies, and those companies, or the call networks that work with them, pay us for the referral. You aren't charged for it and you don't have to hire the company you speak with. The full details are on how it works. We tell you this because the same advice applies to us as to anyone: a referral is a starting point, not a verdict. Check the company before you sign. ## Map listings that aren't real businesses Restoration is one of the categories where map results attract fake listings. Common signs: - **Keyword names,** like "24/7 Water Damage Restoration [City Name]," instead of a real business name. Google's own guidelines don't allow that. - **An address that's a mailbox store, a shared office or a house** with no sign of a business, or no address at all in a category where crews need a shop. - **Many near-identical listings** across neighboring towns, all forwarding to one phone line. - **Reviews that are short, generic and posted in bursts.** Some of these listings forward calls to a real local company, so the work may be fine. The problem is that you don't know who you've hired until someone arrives. ## When the company that shows up isn't the one you called A few businesses take jobs and pass them to subcontractors, keeping a cut. Sometimes that's ordinary overflow during a storm. Sometimes it's the business model. Either way, your contract, your warranty and your dispute rights sit with whoever's name is on the paperwork you sign, which may not be the crew in your basement. Before signing, ask the crew: "Who do you work for, and whose name is on this contract?" If those answers differ, ask who is responsible if something goes wrong. ## A two-minute phone check You can ask these while the water is still running. A legitimate company answers them without hesitation. - **"What's your company's legal name, and where are you based?"** Write it down. You'll check it in a minute. - **"Will your own crew come, or a subcontractor?"** - **"Are your technicians IICRC certified for water damage?"** Certified firms can be checked on the IICRC locator. - **"What does the first visit cost if I decide not to hire you?"** Many companies inspect at no charge; some bill an emergency call fee. Know before they arrive. - **"What will you ask me to sign?"** A work authorization is normal. An assignment of benefits is a bigger step. See before you sign. ## Three records to check - **Your state's business registry**, usually run by the Secretary of State. The legal name should exist and be active. - **Any contractor license or registration** your state, county or city requires. Rules vary a lot. Mitigation alone often doesn't need a license, but rebuilding usually does. - **The IICRC global locator,** which lists certified firms. Proof of liability insurance is worth asking for too, ideally as a certificate sent to you by the insurance agent rather than a photo of one. ## Warning signs, whoever referred them - Won't give a legal business name, or the name on the paperwork differs from the one on the phone. - Pushes you to sign an assignment of benefits before anyone has looked at the damage. - Says your insurance has "already approved" the work before you've opened a claim. - Offers to cover or waive your deductible. See deductible offers. - Wants a large payment up front for emergency drying, which is normally billed after the work or to your insurer. ## Local rules by state Each state section explains its claim rules, insurance regulator and cancellation rights: Alabama, Arkansas, Georgia, Illinois, Indiana, Iowa, Kansas, Kentucky, Maryland, Michigan, Minnesota, Mississippi, Missouri, Nebraska, New York, North Carolina, Ohio, Oklahoma, Pennsylvania, South Carolina, Tennessee, Texas, Virginia, West Virginia, Wisconsin. ## Frequently asked questions **Do plumbers get paid for recommending restoration companies?** Often, yes. Referral fees from restoration companies to plumbers, property managers and others are common in the industry and generally legal. It doesn't mean the recommendation is bad, but it does mean it isn't neutral. Ask the plumber whether they're paid for the referral, and check the company the same way you'd check any other. **Why did a different company show up than the one I called?** You may have called a franchise brand's central line, a call network or lead service that routes calls to participating local companies, or a company that subcontracts jobs. Ask the crew for their legal business name and who your contract will be with before you sign anything. **How can I tell if a Google Maps listing is a real local business?** Look for a real street address you can verify, a business name that isn't just a list of keywords and a city, a website with the same legal name and a license number, and reviews that describe actual jobs. Then ask on the phone for the legal business name and where their crew is based. **Does a referral fee make my bill higher?** Usually not line by line. Insurance restoration work is mostly priced from shared regional price lists, so the referral cost tends to come out of the company's margin rather than appearing on your invoice. It can matter in other ways, like pressure to sign quickly or to approve more work. **How does Local Water & Mold make money?** We're a referral service. Restoration companies, or the call networks that work with them, pay us when a caller is connected to a participating local company. You aren't charged for the referral and aren't obligated to hire the company you speak with. ## Sources - IICRC: Find a certified firm - Google: Guidelines for representing your business on Google - Google: About Local Services Ads - FTC: How to avoid a home improvement scam - NAIC: Find your state insurance department --- Reference # Restoration and insurance glossary The words you'll hear from restoration crews and adjusters after water, mold or fire damage, defined in plain English. 47 terms. ## Types of water damage **Category 1 water**: Clean water from a sanitary source, such as a broken supply line, an overflowing sink with no contaminants, or a water heater. It's mainly a drying job if handled quickly. Water categories explained → **Category 2 water**: Gray water with significant contamination that could cause illness if ingested or touched, such as washing machine or dishwasher discharge or a toilet overflow with urine. Water categories explained → **Category 3 water**: Black water that is grossly contaminated, such as sewage, toilet overflow with feces, or floodwater from rivers and streams. Porous materials it touches are generally removed. Water categories explained → **Class of water damage**: A rating from 1 to 4 under the IICRC S500 standard for how much material is wet and how hard it will be to dry. Class 4 means water is held in dense materials like hardwood, plaster or concrete. **Sudden and accidental**: The insurance test for most covered water damage: a discharge that happened abruptly and unexpectedly, such as a burst pipe, as opposed to gradual damage from a slow leak or lack of maintenance. What insurance covers → **Gradual damage**: Damage that built up over weeks or months, such as rot from a slow drip or a failed shower pan. Usually excluded from homeowners insurance. **Wicking**: Water moving up or along porous materials such as drywall, wood and carpet by capillary action. It's why water damage spreads higher and farther the longer it sits. **Efflorescence**: A white, chalky crust on concrete or masonry walls left when water seeps through and evaporates, leaving minerals behind. A sign of moisture moving through a basement or crawl space wall. ## The restoration job **Mitigation**: The emergency phase of a water damage job: stopping the source, extracting water, removing materials that can't be saved, and drying the structure so damage doesn't spread. **Restoration (reconstruction)**: Putting the home back after mitigation: replacing drywall, insulation, flooring, cabinets, paint and trim. Often billed separately and sometimes done by a different contractor. **Extraction**: Removing standing water and water held in carpet and pad with pumps and truck-mounted or portable extractors. It's much faster than evaporating the same water. **Air mover**: A high-velocity fan that pushes air across wet surfaces to speed evaporation during structural drying. **Dehumidifier (LGR)**: A machine that removes moisture from the air. Low-grain refrigerant (LGR) dehumidifiers used in restoration can keep pulling water out of air that's already fairly dry. **Moisture mapping**: Using moisture meters and thermal imaging to find and record how far water traveled into walls, floors and ceilings, so drying and removal can be targeted. **Dry standard**: The moisture reading of a material in an unaffected part of the same building. Drying is complete when wet materials reach that reading, not after a fixed number of days. How long drying takes → **Drying log**: A daily record of moisture readings, temperature and humidity during drying. It documents that drying was done properly and is often requested by insurers. **Antimicrobial**: A product applied to clean surfaces after gray or black water, or during mold remediation, to limit microbial growth. It doesn't replace removing contaminated materials and drying. **Containment**: Plastic sheeting and sealed openings that isolate a mold or sewage work area so spores and debris don't spread to the rest of the house. **Negative air**: Running an air scrubber that exhausts air out of a contained work area, keeping it at lower pressure than the rest of the house so contaminated air doesn't escape. **HEPA**: High-efficiency particulate air filtration, used in vacuums and air scrubbers during mold and fire cleanup to capture fine particles and spores. **IICRC**: The Institute of Inspection, Cleaning and Restoration Certification, a nonprofit that certifies technicians and develops industry standards for water, mold and fire restoration. **IICRC S500**: The ANSI/IICRC standard for professional water damage restoration. It defines water categories and classes and the procedures for drying. **IICRC S520**: The ANSI/IICRC standard for professional mold remediation, covering assessment, containment, removal, cleaning and verification. Black mold guide → **Xactimate**: Estimating software widely used by insurers, adjusters and restoration companies to price repairs line by line. Many contractors bill insurers through it. ## Insurance terms **Deductible**: The amount you pay toward a covered claim before insurance pays. Some policies have a separate, higher deductible for wind, hail or water damage. **Actual cash value (ACV)**: Payment based on what damaged property was worth at the time of loss: replacement cost minus depreciation for age and wear. **Replacement cost value (RCV)**: Payment based on the cost to repair or replace damaged property with new material of like kind and quality, without deducting depreciation. **Recoverable depreciation**: On a replacement cost policy, the depreciation an insurer may hold back at first and pay once repairs are completed and documented. **Proof of loss**: A formal, often sworn, statement of the amount you're claiming and how the loss happened. Policies set a deadline after the insurer requests it, and state rules set how quickly insurers must respond. Protecting your claim → **Additional living expenses (ALE)**: Coverage for the extra cost of living elsewhere, such as a hotel and meals, while a covered loss makes your home unlivable. Also called loss of use or Coverage D. **Water backup endorsement**: An add-on to a homeowners policy that covers damage from water backing up through sewers or drains, or overflowing from a sump pump. Standard policies exclude it. **National Flood Insurance Program (NFIP)**: The federal flood insurance program run by FEMA. Homeowners policies exclude flood, so flood coverage comes from the NFIP or a private flood insurer, usually with a 30-day waiting period. **Adjuster**: The person who investigates a claim and estimates the loss for the insurer. Staff and independent adjusters work for the insurance company. **Public adjuster**: A licensed adjuster you hire to prepare and negotiate your claim, usually for a percentage of the settlement. Licensing and fee limits vary by state. **Appraisal clause**: A policy provision for resolving disputes over the amount of a loss: each side picks an appraiser, and an umpire decides where they disagree. **Assignment of benefits (AOB)**: A document that transfers your right to insurance payments to a contractor, who then bills and negotiates with your insurer. Read it carefully before signing; it can limit your control over the claim. **Work authorization**: A contract that lets a restoration company start work and usually sets how it will be paid. Different from an assignment of benefits, but still worth reading before signing. ## House and weather terms **Main water shutoff**: The valve that stops all water into the house, usually where the water line enters through the foundation, near the meter. In cold climates it's often in the basement; in warm climates it may be outside or in a garage. **Sump pump**: A pump in a pit at a low point of a basement or crawl space that removes groundwater collected by drains around the foundation. **Backwater valve**: A valve on a sewer line that lets wastewater flow out but closes if sewage starts flowing back toward the house. **Vapor barrier**: Plastic sheeting laid over a crawl space floor, or installed in walls, to slow moisture moving through. In crawl spaces it's the first step toward controlling ground moisture. Crawl space guide → **Crawl space encapsulation**: Sealing a crawl space's floor, walls and vents with a heavy liner and drying it with a dehumidifier or conditioned air. Crawl space guide → **Ice dam**: A ridge of ice at the edge of a roof that traps melting snow behind it, forcing water under shingles and into ceilings and walls. **Pipe-freeze night**: On this site, a night with a low at or below 20°F, the temperature at which uninsulated pipes in unheated spaces are at serious risk of freezing. Counted from NOAA daily data. Our methodology → **Freeze-thaw day**: On this site, a day with a low at or below 32°F and a high above it. Frequent freeze-thaw cycles drive ice dams and foundation cracking. **Heavy-rain day**: On this site, a day with 1 inch or more of precipitation, when sump pumps run hardest and storm sewers are most likely to back up. **Muggy night**: On this site, a night with a low of 65°F or warmer, a simple sign of humid summer air that feeds basement and crawl space mold. --- Data # Water damage risk by state Old plumbing, hard freezes, heavy rain and humid summers are what turn into water damage and mold claims. Here's how the 25 states we cover compare, built from 1,822 counties of Census housing data and ten years of NOAA daily weather. Key findings - **Oldest housing:** New York (70%), Pennsylvania (67%) and Illinois (63%) have the largest shares of homes built before 1980. The newest housing is in Georgia (31%), South Carolina (33%) and Texas (33%). - **Most pipe-freeze nights** (lows of 20°F or colder) for the typical resident: Minnesota (84 a year), Wisconsin (64 a year) and Iowa (59 a year). - **Most heavy-rain days** (1 inch or more): Mississippi (16.8 a year), Arkansas (16.1 a year) and Alabama (15.4 a year). - **Most muggy nights** (lows of 65°F or warmer, the humid air that feeds mold): Texas (153 a year), Mississippi (127 a year) and Alabama (113 a year). Water damage risk factors by state. Select a column heading to sort. | State | Homes | Built before 1980 | Built before 1960 | Pipe-freeze nights / yr | Freeze-thaw days / yr | Heavy-rain days / yr | Muggy nights / yr | Coldest county | | Alabama | 2,337,265 | 42% | 16% | 3 | 36 | 15.4 | 113 | Colbert County (7) | | Arkansas | 1,394,673 | 40% | 13% | 9 | 52 | 16.1 | 97 | Madison County (18) | | Georgia | 4,541,835 | 31% | 12% | 3 | 36 | 12.9 | 103 | Fannin County (12) | | Illinois | 5,457,452 | 63% | 38% | 40 | 82 | 7.2 | 42 | Jo Daviess County (57) | | Indiana | 2,976,568 | 55% | 31% | 33 | 83 | 7.9 | 41 | Steuben County (41) | | Iowa | 1,437,699 | 62% | 38% | 59 | 92 | 7.1 | 32 | Dickinson County (81) | | Kansas | 1,293,635 | 56% | 32% | 32 | 87 | 8.4 | 70 | Finney County (53) | | Kentucky | 2,023,116 | 47% | 22% | 19 | 71 | 11.8 | 63 | Lewis County (26) | | Maryland | 2,265,752 | 47% | 21% | 15 | 73 | 9.2 | 66 | Garrett County (42) | | Michigan | 4,622,236 | 62% | 36% | 44 | 88 | 4.8 | 23 | Iron County (111) | | Minnesota | 2,545,030 | 52% | 29% | 84 | 85 | 5.5 | 17 | Lake County (120) | | Mississippi | 1,341,114 | 41% | 14% | 3 | 30 | 16.8 | 127 | Alcorn County (9) | | Missouri | 2,651,176 | 51% | 24% | 27 | 75 | 10.4 | 70 | Nodaway County (47) | | Nebraska | 863,444 | 57% | 32% | 56 | 101 | 6.2 | 40 | Box Butte County (82) | | New York | 4,906,755 | 70% | 46% | 40 | 88 | 6.7 | 31 | Essex County (88) | | North Carolina | 4,895,668 | 34% | 14% | 6 | 55 | 11.5 | 84 | Avery County (27) | | Ohio | 5,292,391 | 63% | 38% | 30 | 79 | 5.6 | 39 | Morrow County (38) | | Oklahoma | 1,775,127 | 49% | 21% | 13 | 63 | 11.0 | 99 | Texas County (30) | | Pennsylvania | 5,806,452 | 67% | 45% | 29 | 89 | 8.5 | 38 | Potter County (58) | | South Carolina | 2,443,039 | 33% | 12% | 2 | 35 | 12.4 | 112 | Cherokee County (5) | | Tennessee | 3,143,670 | 41% | 18% | 10 | 58 | 13.1 | 79 | Johnson County (23) | | Texas | 12,113,403 | 33% | 12% | 2 | 17 | 11.2 | 153 | Deaf Smith County (26) | | Virginia | 2,538,662 | 38% | 15% | 14 | 74 | 9.3 | 65 | Tazewell County (26) | | West Virginia | 861,325 | 56% | 32% | 25 | 86 | 6.7 | 31 | Randolph County (42) | | Wisconsin | 2,778,572 | 57% | 33% | 64 | 92 | 6.5 | 16 | Vilas County (110) | Covers counties named "… County" in each state; independent cities and New York City's boroughs aren't included. Housing shares are weighted by housing units. Weather counts are county averages weighted by population, so they describe the typical resident's county. Download the data (CSV) ## Why these numbers predict water damage - Homes built before 1980 are more likely to have galvanized steel supply pipes, cast iron drains and original water heater connections that corrode and fail, and less insulation around pipes in exterior walls and crawl spaces. - Pipe-freeze nights, lows of 20°F or colder, are when pipes in unheated spaces, exterior walls and crawl spaces are at serious risk of freezing and splitting. - Freeze-thaw days drive ice dams on roofs and cracking in foundations and driveways. - Heavy-rain days, an inch or more in 24 hours, are when basements flood, sump pumps run hardest and sewers back up. - Muggy nights signal the humid summer air that keeps basements and crawl spaces damp enough for mold. ## County-level detail Every state links to its own Water Damage Risk Index, which ranks each county on the same factors, and every county page breaks down its own housing and weather. Use the state names in the table above, or choose your state. ## Method and sources Housing data comes from the U.S. Census Bureau's American Community Survey, ACS 2024 5-year estimates (2020-2024). Weather counts come from NOAA's nClimGrid-Daily county averages for 2015–2024. Full definitions, formulas and limits are in our methodology. You're welcome to cite these figures; please link to this page. ## Frequently asked questions **Which state has the oldest homes for water damage risk?** Among the 25 states we cover, New York has the largest share of homes built before 1980, at 70%, followed by Pennsylvania (67%) and Illinois (63%). Older homes are more likely to have galvanized steel or cast iron pipes, older water heaters and less insulation around plumbing. **Which states have the most frozen pipe risk?** By pipe-freeze nights, nights at or below 20°F, the typical resident of Minnesota sees about 84 a year, Wisconsin about 64, and Iowa about 59, based on NOAA daily county data for 2015–2024. **Which states get the most heavy rain?** Mississippi averages about 16.8 days a year with an inch or more of rain for the typical resident, followed by Arkansas (16.1) and Alabama (15.4). Heavy-rain days are when basements flood, sump pumps fail and sewers back up.